AND STANDARDS Sample Clauses

AND STANDARDS. The Supplier shall be responsible for obtaining and maintaining all licences, authorisations, consents or permits required in relation to the performance of its obligations under this Framework Agreement and any Call-Off Agreement. The Supplier shall comply with the Standards in performing its obligations under this Framework Agreement and as set out in Schedule 13.

AND STANDARDS. The Concessionaire shall comply with the specifications and standards set forth in this Schedule 4 while fulfilling its obligations under the Concession Agreement. For the avoidance of any doubt, the Concessionaire shall, in addition to the standards specified in this Schedule, adopt any other relevant standards required to be adopted in accordance with Applicable Laws and good industry practice.

AND STANDARDS. 6.1 The Subscriber shall at all times ensure that the Products are produced, sold or otherwise disposed of, supplied, used and maintained and that the Services are provided by or for the Subscriber in accordance and full compliance with all licences, permits, legislations, registrations, regulations, restrictions, standards and codes applicable in the Territory under which the Subscriber or as the case may be its Affiliates, its suppliers, its contractors, sub-contractors or its or their employees or its or their agents are or may be lawfully required to operate in relation to the production, sale, supply, disposition, use and maintenance of the Products and the provision of the Services as any of the same may be in force or applicable from time to time during the term of this Agreement. 6.2 Where there is no licence, permit, legislation, registration, regulation, restriction, code or standard applicable, the Subscriber shall ensure that Products are produced, sold or otherwise disposed of, supplied, used and maintained, at a standard at least equivalent to Satisfactory Quality and that Services are provided in accordance with good industry practice. 6.3 In all cases the Subscriber shall ensure that the production, sale, supply, disposition and use of all Products and the provision of all Services is carried out in compliance with all relevant legislation and regulations relating to health and safety and protection of the environment.

AND STANDARDS. 4.1.1. Technical Specifications and Drawings: a) The AMISP shall ensure that the Solution comply with the Applicable Law, technical specifications and other provisions of the Contract. b) The Solution supplied under this Contract shall conform to the standards mentioned in the Schedule F of this Contract. When no applicable standard is mentioned, the standard shall be equivalent or superior to the official standards whose application is appropriate to the country of origin of the Goods. 4.1.2. Wherever references are made in the Contract to codes and standards in accordance with which the Solution shall be executed, the edition or the revised version of such codes and standards shall be those specified in the scope of work. During Contract execution, any changes in any such codes and standards shall be applied only after approval by [Utility] and shall be treated as Change Order in accordance with Article 14.

AND STANDARDS. The Provider must participate as appropriate in relevant quality assurance programmes to the extent applicable to the Provider and this Arrangement, e.g. (a) HIQA programmes (b) Engage in Healthcare Audits conducted by: - the Internal Audit Division Healthcare Audit Function - - the National Centre for Clinical Audit (NCCA) National Office of Clinical Audit (NOCA)

AND STANDARDS. The Provider must participate as appropriate in relevant quality assurance programmes to the extent applicable to the Provider and this Arrangement, e.g. 1. HIQA programmes 2. Engage in Healthcare Audits conducted by:

AND STANDARDS. The construction activities and final Works shall comply with the statutory requirements as amended to date and relevant guidelines and regulations, inter alia: The Occupational Health and Safety (Act 85 of 1993). Environmental Conservation Act (Act 50 of 2003). Civil Aviation Act (Act 13 of 2009) Municipal bylaws and regulations. Standards and Specifications of the ACSA. Standards and Specifications of the Supply Authority. Applicable relevant standards and codes of practice, whether BS, IEC, NRS or SANS. Should there be conflict between the Specifications and the Drawings then Parts shall be considered in the following order of priority: Scope of Work (Project Specification) Bill of Quantities Drawings Standard Technical Specifications Should the Contractor note an inconsistency between various Parts and Sections of the Document, the Contractor shall be responsible to notify the Employer and obtaining clarification or instructions prior to ordering or installing equipment.

AND STANDARDS. The following is a list of documents, specifications or standards that will apply to the work performed within the scope of this proposal or any contract arising from this proposal. Any deviation from these documents, specifications or standards shall be stated in this proposal and shall form part of any contract arising from this proposal. 2.1 Molichem Medicines Inc. Documents Xxxxxxxxx Wellcome Co. TCPW95/0007 Nomenclature and Description July 13, 1995 Xxxxxxxxx Wellcome Co. TCPW95/0005 Method of Manufacture July 13, 1995 Xxxxxxxxx Wellcome Co. TCPW95/0006 Preparation of Reference July 13, 1995 Standards Magellan Laboratories - TTP-MMR-M001 9 Certificate of Analysis - November 06, 2000 Analytical Characterization of Moli1901 (Duramycin) Use or disclosure of the data contained on this sheet is subject to the restriction on the title page of this proposal.

AND STANDARDS. 3.1. Goodwill Associated With Licensor's Trademark and Trade Dress. Licensee acknowledges that Licensor has valuable goodwill and other rights in the Licensed Marks and Licensor's Trade Dress. Licensee agrees that it shall not at any time do or cause to be done directly or indirectly any act contesting, or in any way impairing any part of the Licensor's right, title or interest in the Licensed Marks and Licensor's Trade Dress. Without limiting the foregoing, Licensee shall during the term of this Agreement use reasonable efforts to ensure that use of the Licensed Marks and Licensor's Trade Dress is in accordance with use which is to the best advantage and protection of Licensor's goodwill in Licensed Marks and said Trade Dress.

AND STANDARDS. PRI in its performance hereunder shall comply with all specifications and quality control standards set forth in Schedule A and Schedule D, attached hereto and made a part hereof ("specifications"). If PRI shall fail to meet such specifications with respect to any Cups, such Cups shall be returned PRI at PRI's sole expense and PRI shall, within thirty (30) days of its receipt of such defective Cups, either replace such Cups or refund (or credit) the entire amount of any base price paid for such Cups.