STANDARDS AUSTRALIA Sample Clauses

STANDARDS AUSTRALIA. This document contains Standards Australia Ltd copyrighted material that is distributed by SAI Global Ltd on Standards Australia Ltd’s behalf. It may be reproduced and modified in accordance with the terms of SAI Global Ltd’s Licence 1901-c021 to Tablelands Regional Council (Licensee). All amended, marked up and licensed copies of this document must be obtained from the Licensee. Standards Australia Ltd copyright material is not for resale, reproduction or distribution in whole or in part without written permission from SAI Global Ltd: tel +00 0 0000 0000 or xxxxxxxxx@xxxxxxxxx.xxx. A copy of AS4000-1997 General Conditions of Contract and Annexures (as current at the date of acceptance of tender) forms part of this Contract notwithstanding that a copy is not physically included. A copy of the AS4000 – 1997 General Conditions of Contract can be obtained from SAI Global by contacting (00) 0000 0000 or xxxxxxxxx@xxxxxxxxx.xxx or by visiting the website xxx.xxxxxxxxx.xxx. In Annexure Part A, items or words which have been struck through are deleted from Annexure Part A and items or words which have been underlined have been added to Annexure Part A. EXECUTED AS AN AGREEMENT EXECUTION BY THE PRINCIPAL SIGNED for and on behalf of Tablelands Regional Council in accordance with the Council's local laws and in the presence of: Signature of witness Name of witness (block letters) Date: / / ) ) ) ) ) ) ) ) ) Chief Executive Officer Date: / / EXECUTION BY THE CONTRACTOR (WHERE CONTRACTOR IS A CORPORATION) SIGNED for and on behalf of the Contractor in accordance with its Constitution and Section 127 of the Corporations Xxx 0000 in the presence of: Signature of witness Name of witness (block letters) Date: / / ) ) ) ) ) ) ) ) ) Director Director/Secretary Date: / / EXECUTION BY CONTRACTOR (WHERE CONTRACTOR IS NOT A CORPORATION) SIGNED for and on behalf of the Contractor by its authorised representative in the presence of: Signature of witness Name of witness (block letters) Date: / / ) ) ) ) ) ) ) ) ) Signature Name of authorised representative Date: / / ANNEXURE to the Australia Standard General Conditions of Contract AS4000-1997 PART A This Annexure shall be completed and issued as part of the tender documents and, subject to any amendments to be incorporated into the Contract, is to be attached to the General Conditions of Contract and shall be read as part of the Contract. Item 1 Principal (clause 1) Tablelands Regional Council ABN 77 642 342 175 2 Principal's addre...
Sample 1Sample 2See All (5)
AutoNDA by SimpleDocs
STANDARDS AUSTRALIA. Australian Standard Licensed to Mr Xxxxx Xxxxxxx on 4 December 2012. 1 user personal user licence only. Storage, distribution or use on network prohibited (10344892). Identification of the contents of pipes, conduits and ducts 1 SCOPE This Standard specifies means of identifying the contents of pipes, conduits, ducts and sheathing used to contain fluids, or for the distribution of electrical or communications services in land installations and on board ships, by the use of colours, words and symbols. It is not intended to apply to buried or normally inaccessible services. However, the general principles may be applied when considering those services.
Sample 1

Related to STANDARDS AUSTRALIA

  • Information Technology Accessibility Standards Any information technology related products or services purchased, used or maintained through this Grant must be compatible with the principles and goals contained in the Electronic and Information Technology Accessibility Standards adopted by the Architectural and Transportation Barriers Compliance Board under Section 508 of the federal Rehabilitation Act of 1973 (29 U.S.C. §794d), as amended. The federal Electronic and Information Technology Accessibility Standards can be found at: xxxx://xxx.xxxxxx-xxxxx.xxx/508.htm.

  • Applicable Technical Standards The Applicable Technical Requirements and Standards that apply to the Customer Facility and the Interconnection Facilities are identified in Schedule D to this ISA.

  • Technical Standards The Generation System shall be installed and operated by the Interconnection Customer consistent with the requirements of this Agreement; the Technical Requirements; the applicable requirements located in the National Electrical Code (NEC); the applicable standards published by the American National Standards Institute (ANSI) and the Institute of Electrical and Electronic Engineers (IEEE); and local building and other applicable ordinances in effect at the time of the installation of the Generation System.

  • Standards for Network Elements 1.8.1 BellSouth shall comply with the requirements set forth in the technical references, as well as any performance or other requirements identified in this Agreement, to the extent that they are consistent with the greater of BellSouth’s actual performance or applicable industry standards.

  • COUNTY’S QUALITY ASSURANCE PLAN The County or its agent will evaluate the Contractor’s performance under this Contract on not less than an annual basis. Such evaluation will include assessing the Contractor’s compliance with all Contract terms and conditions and performance standards. Contractor deficiencies which the County determines are severe or continuing and that may place performance of the Contract in jeopardy if not corrected will be reported to the Board of Supervisors. The report will include improvement/corrective action measures taken by the County and the Contractor. If improvement does not occur consistent with the corrective action measures, the County may terminate this Contract or impose other penalties as specified in this Contract.

  • Human and Financial Resources to Implement Safeguards Requirements 6. The Borrower shall make available necessary budgetary and human resources to fully implement the EMP and the RP.

  • Manufacturing Standards All forest products except poles, produced and sold under this contract will be manufactured to maximize the amount of logs meeting preferred log lengths and to achieve the average log length listed. Agreement No. Sort # Scaling Rule 97318 3 WS Average Log Length Preferred Log Lengths "WS" indicates that west side scaling rules apply. Minimum trim is 8 inches per scaling segment for west side scaling rules. "ES" indicates that east side scaling rules apply. Minimum trim is 4 inches per scaling segment for east side scaling rules. Poles produced under this contract will be manufactured to ANSI specifications (American National Standard Specifications and Dimensions for Wood Poles), in force at the time of signing this contract.

  • SUPPLIER STANDARDS OF CONDUCT Accenture is committed to conducting its business free from unlawful, unethical or fraudulent activity. Supplier will act in a manner consistent with the ethical and professional standards of Accenture as described in the Accenture Supplier Standards of Conduct, including prompt reporting of unlawful, fraudulent or unethical conduct. A copy of these standards can be found at xxxxxxxxx.xxx/xx- en/company-ethics-code.

  • Financial Management Standards The financial management systems of Grantee must meet the following standards:

  • Procurement Standards For projects being managed by the Local Government and on the State highway system or that include state funding, the Local Government must obtain approval from the State for its proposed procurement procedure for the selection of a professional services provider, a contractor for a construction or maintenance project, or a materials provider.

Time is Money Join Law Insider Premium to draft better contracts faster.