ANCILLARY WORKS Sample Clauses

ANCILLARY WORKS. The contractor shall submit to Engineer in charge in writing the details of all ancillary works including layout and specifications to be allowed for its constructions. Ancillary work shall not be taken up in hand unless approved by Engineer in charge. The Engineer in charge reserves the right to suggest modification or make complete changes in the layout and specifications proposed by the Contractor at any stage to ensure the safety on the work site. The contractor shall carry out all such modifications to the ancillary works at his own expenses as ordered by the Engineer in charge.
Sample 1Sample 2Sample 3See All (27)
AutoNDA by SimpleDocs
ANCILLARY WORKS. In the event that any gauging xxxx or other measuring device is constructed as part of the Project in terms of Article 4(1)(c) but which is not or has not been included as an appurtenant ancillary work in either sub-phase 1A or sub-phase 1B, the respective Capital Cost shares of the Parties shall be as follows: Swaziland (0.06589 + 0.401 x is) it South Africa (0.53311 + 0.401 x ir) it 3. COST APPORTIONMENT DETERMINATION For the purpose of cost apportionment, KOBWA shall prepare revised estimates of Total Cost (comprising separate estimates of the total cost of the Driekoppies and Maguga Dams) at least four months before the beginning of each financial year in accordance with the principles set out in Section 4 below. Subject to the approval of the JWC, such estimates shall be used to determine the proportions referred to in Articles 5(6)(b), 5(6)(c) and 6(3) in accordance with the formulae set out in Section 2 above. Such proportions shall be used during the financial year in question to determine the payments due by the Parties to KOBWA in terms of Article 11(3)(b). Provided that from a date to be determined by the JWC following the completion of both Driekoppies and Maguga Dams, such proportions shall be set equal to those determined for the financial year in which such date falls and no further revision to Total Cost shall be made.
Sample 1Sample 2
ANCILLARY WORKS. The contractor shall submit to Engineer-in-charge in writing the details of all ancillary works including layout and specifications to be followed for its construction. Ancillary work shall not be taken up in hand unless approved by Engineer-in-charge. The Engineer-in-charge reserves the right to suggest modifications or make complete chages in the layout and specifications proposed by the contractor at any stage to ensure the safety on the work site. The contractor shCaolnltraccatorrry out all such modification to tNhoe oafnccoirlrleacrtyionworks at his own exUpneivnesresistyaEsnogrindeeerred by Engineer-in-charge.
Sample 1
ANCILLARY WORKS. S5.1.1 As AMSA’s protective coating and refurbishment projects are often in remote locations and incorporate other works, the Service Provider may be required to undertake:
Sample 1
ANCILLARY WORKS. In the event that any gauging xxxx or other measuring device is constructed as part of the Project in terms of Article 4 (l) (c) but which is not or has not been included as an appurtenant ancillary work in either sub-phase 1A or sub-phase 1B, the respective Capital Cost shares of the Parties shall be as follows: Swaziland (0.06589 + 0.401 x is) it South Africa (0.53311 + 0.401 x ir) it
Sample 1
ANCILLARY WORKS 
Sample 1Sample 2Sample 3See All (4)

Related to ANCILLARY WORKS

  • Licensed Materials The materials that are the subject of this Agreement are set forth in Appendix A ("Licensed Materials").

  • Embedded Software To the extent any goods contain Embedded Software (defined below) that is not Buyer’s Property, no title to such Embedded Software shall pass to Buyer, and Supplier shall grant Buyer, its customers and all other users a non-exclusive worldwide, irrevocable, perpetual, royalty-free right to use, load, install, execute, demonstrate, market, test, resell, sublicense and distribute such Embedded Software as an integral part of such goods or for servicing the goods (the “Buyer-Required License”). If such Embedded Software or any part thereof is owned by a third party, prior to delivery, Supplier shall obtain the Buyer-Required License from such third-party owner. “Embedded Software” means software necessary for operation of goods and embedded in and delivered as an integral part of goods.

  • Licensed Software Computer program(s) provided by Contractor in connection with the Deliverables, subject to Section 14 of this Contract.

  • Personnel Equipment and Material Engineer shall furnish and maintain, at its own expense, quarters for the performance of all Engineering Services, and adequate and sufficient personnel and equipment to perform the Engineering Services as required. All employees of Engineer shall have such knowledge and experience as will enable them to perform the duties assigned to them. Any employee of Engineer who, in the reasonable opinion of County, is incompetent or whose conduct becomes detrimental to the Engineering Services shall immediately be removed from association with the Project when so instructed by County. Engineer certifies that it presently has adequate qualified personnel in its employment for performance of the Engineering Services required under this Contract, or will obtain such personnel from sources other than County. Engineer may not change the Project Manager without prior written consent of County.

  • Work Products Grantee shall provide CalRecycle with copies of all final products identified in the Work Plan. Grantee shall also provide CalRecycle with copies of all public education and advertising material produced pursuant to this Agreement. WORKERS’ COMPENSATION/LABOR CODE

  • Creative Work The Executive agrees that all creative work and work product, including but not limited to all technology, business management tools, processes, software, patents, trademarks, and copyrights developed by the Executive during the term of this Agreement, regardless of when or where such work or work product was produced, constitutes work made for hire, all rights of which are owned by the Employer. The Executive hereby assigns to the Employer all rights, title, and interest, whether by way of copyrights, trade secret, trademark, patent, or otherwise, in all such work or work product, regardless of whether the same is subject to protection by patent, trademark, or copyright laws.

  • Equipment and Materials Contractor at its sole cost and expense shall provide and furnish all tools, labor, materials, equipment, transportation services and any other items (collectively, "Equipment") which are required or necessary to perform the Services in a manner which is consistent with generally accepted standards of the profession for similar services. Notwithstanding the foregoing, District shall not be responsible for any damages to persons or property as a result of the use, misuse or failure of any Equipment used by Contractor of the Contracted Parties, even if such Equipment is furnished, rented or loaned to Contractor or the Contracted Parties by District. Furthermore, any Equipment or workmanship that does not conform to the regulations of this Agreement may be rejected by District and in such case must be promptly remedied or replaced by Contractor at no additional cost to District and subject to District’s reasonable satisfaction.

  • Derivative Works Constellation Beers shall acquire no ownership rights in the Licensed Intellectual Property or derivative works based thereon or any intellectual property deemed to be owned by Marcas Modelo or Modelo Group as a result of this Agreement. Constellation Beers shall, at any time requested by Marcas Modelo or Modelo Group, whether during or subsequent to the term hereof, disclaim in writing any such property interest or ownership in the Licensed Intellectual Property.

  • JOINT WORK PRODUCT This Agreement is the joint work product of H-GAC and the Contractor. This Agreement has been negotiated by H-GAC and the Contractor and their respective counsel and shall be fairly interpreted in accordance with its terms and, in the event of any ambiguities, no inferences shall be drawn against any party.

  • Proprietary Materials Each of the Parties shall own its own intellectual property including without limitation all trade secrets, know-how, proprietary data, documents, and written materials in any format. Any materials created exclusively by IPS for the School shall be owned by IPS, and any materials created exclusively by Operator for the School shall be Operator’s proprietary material. The Parties acknowledge and agree that neither has any intellectual property interest or claims in the other Party’s proprietary materials. Notwithstanding the foregoing, materials and work product jointly created by the Parties shall be jointly owned by the Parties and may be used by the individual Party as may be agreed upon by both Parties from time to time.

Time is Money Join Law Insider Premium to draft better contracts faster.