COMPLIANCE WITH HEALTH, SAFETY, AND ENVIRONMENTAL REGULATIONS The Contractor, it’s Subcontractors, and their respective employees, shall comply fully with all applicable federal, state, and local health, safety, and environmental laws, ordinances, rules and regulations in the performance of the services, including but not limited to those promulgated by the City and by the Occupational Safety and Health Administration (OSHA). In case of conflict, the most stringent safety requirement shall govern. The Contractor shall indemnify and hold the City harmless from and against all claims, demands, suits, actions, judgments, fines, penalties and liability of every kind arising from the breach of the Contractor’s obligations under this paragraph.
Personnel Requirements and Documentation Grantee will;
Quality Assurance Requirements There are no special Quality Assurance requirements under this Agreement.
Safety Orientation All employees shall be certified in Safety Orientation. Safety Orientation shall consist of three parts: PART 1 - the CODC Interactive Rights and Responsibilities course; PART 2 - the XXXX course or equivalent, and PART 3 - Employer or Owner Project Specific Training. It is the responsibility of each employee to hold current certification and maintain certification in part 1 and Part 2. The Employer or Owner shall provide to each Employee before commencing work with PART 3 - Employer or Owner Project Specific Training. Each Employee shall be on the payroll and paid while receiving PART 3 training. As a condition of employment it is the sole responsibility of each and every employee to obtain, hold and maintain all current certification(s) in any and all legislated safety training requirements (i.e. WHMIS, Fall Arrest, etc.) that are trade specific. Supporting documentation of all legislated training must be provided by the employee to the Union prior to dispatch and to the employer upon hire and may be further requested by the employer at any time during the duration of their employment. Prior to the expiration of any certification, the Employer will notify the Employee of the pending expiration and give the Employee reasonable time to renew their certification. Further, prior to arriving at site, employees shall hold current qualification(s) for the specific tasks and equipment identified in the dispatch request. If the employee has to be trained after dispatch, all costs borne by the Employer shall be reimbursed by the Training Fund. The CODC Harassment Policy and Procedures, including the provisions regarding General Harassment and as amended from time to time shall be the minimum standard of this Agreement.
Safety and Compliance The Company commits to make all management and employees aware of all the changes to the Occupational Health and Safety Act and Regulations. This should be done via training courses and or union seminars. The conducting of the training and or seminars shall be at times convenient to the company.
Compliance with Data Privacy and Security Laws and Standards Contractor shall comply with all applicable State and federal data privacy and data security laws, rules, and regulations.
Human and Financial Resources to Implement Safeguards Requirements 6. The Borrower shall make available necessary budgetary and human resources to fully implement the EMP and the RP.
COMPLIANCE WITH THE CONTRACT WORK HOURS AND SAFETY STANDARDS ACT (1) Overtime requirements. No contractor or subcontractor contracting for any part of the contract work which may require or involve the employment of laborers or mechanics shall require or permit any such laborer or mechanic in any workweek in which he or she is employed on such work to work in excess of forty hours in such workweek unless such laborer or mechanic receives compensation at a rate not less than one and one-half times the basic rate of pay for all hours worked in excess of forty hours in such workweek.
Compliance with Standards Although the standards for workmanship, material, and equipment have been selected in these specifications as a basis of reference, standards and specifications of the other bank member countries and recommendations of standards international organizations will be acceptable provided they are substantially equivalent to the designated standards and provided furthermore that the contractor submits for approval detailed specifications which he proposes to use. Reference to brand names or catalog numbers if any in these specifications have been made only for that equipment for which it has been determined that a degree of standardization is necessary to maintain certain essential features. And in certain cases such references have also been made for purposes of convenience to specify the requirements, in either case offers of alternative goods, which have similar characteristics and provide performance and quality at lease equal to those specified are acceptable. If the contractor offers materials, equipment, design calculations or tests, which conform to standards other than those specified, full details of the differences between the proposed standards and that specified in so far as they affect the design or purpose of the equipment, are to be supplied by the contractor if called upon to do so by the engineer, where required by the engineer for approval purposes, the contractor shall supply, without charge, duplicate copies of the proposed standards with English translations of the relevant portions. The contractor shall have available in his place of business (or in his supplier’s works) the relevant copies of standards or codes used for the use of the Engineer.
Labor-Management Cooperation When an Appointing Authority initiates a planning process or management study which is anticipated to result in layoff, the Appointing Authority will meet and confer with the Local Union during the decision planning phase and again during the implementation planning phase. The Appointing Authority and the Local Union shall enter into negotiations regarding a Memoranda of Understanding upon request of either party to modify this Agreement regarding the implementation plans which shall include, but are not limited to, the following: • Length of layoff notice; • Job and retraining opportunities; • Alternative placement methods; • Early retirement options pursuant to M.S. 43A.24, Subd. 2(i); • Bumping/vacancy options for part-time employees to preserve their insurance eligibility or contribution; and • Other methods of mitigating layoff or their effect on employees.
