Linear Sample Clauses

Linear. Mean that the thrust develop linearly with the throttle setting, has more resolution at lower half of the throttle stick.
Linear. Mean that the thrust develop linearly with the throttle setting, has more resolution at lower half of the throttle stick. This is the preferred factory setting. HALF EXPO: An intermediate setting between the previous two modes. Test functions The FADEC provides testing functions to the starter motor, glow plug, pump and both solenoid valves. These test screens are only available when the FADEC is on “Trim Low” status, that is to say, recently powered up and receiving a STOP signal from the TX. Pressing the (-) button (under the “ON” reading on the screen) will energize the selected device and pressing (+) will shut down. Special care should be taken when testing the pump, as it is possible that fuel can be pumped into the engine, flooding it, and causing a hot start on next startup. Turbine starting and running Always set-up and confirm the operation of your Auto-start installation on the test- stand, before installing into your model. The present version of auto start uses only one channel for the entire engine functions: To trigger the auto start cycle, the process is as follows:
Linear. The linear covariance function is a non-stationary covariance function leading to a model of all linear functions: =
Linear. A linear repayment means that the bond loan is repaid during the term by paying a fixed amount on a periodic basis so that, after the maturity date, the entire principal has been repaid to the bond holder. Deposit Date The date on which the amount of the Principal of the Corporate Bond is deposited by or on behalf of the Bondholder into the bank account indicated by the Issuer plus the legally required cooling-off period of fourteen days. Supervisory Restrictions The Restrictions on the Issuance and Transfer of Corporate Bonds as laid down in or pursuant to Sections 3:5 and 5:3 of the Dutch Financial Supervision Act (Wet op het financieel toezicht, Wft) as it is currently stated, as it will be stated after amendment or any legislation or regulations that may replace it. Second, third, fourth and fifth Issuance (Any) Second Offer and Issue of Bonds, or Issuance 13, which can take place. (Any) Third Offer and Issue of Bonds, or Issuance 14, which can take place. (Any) Fourth Offer and Issue of Bonds, or Issuance15, which can take place. (Any) Fifth Offer and Issue of Bonds, or Issuance 16, which may take place. Business day A day, other than a Saturday or Sunday and not being a generally recognised public holiday as referred to in section 3(1) of the General Termination Act or a day assimilated to a generally recognised public holiday in section 3(2) or (3) of that Act, on which the banks in the Netherlands are open and make payment transactions. Use of plural To the extent that the terms used herein are used in plural in this Agreement, they shall be construed in accordance with the definitions given above.
Linear. Edit values by dragging the knob upward or downward. 3 In the AutoStop Setting area, specify if and when you want the audio to stop auto- matically.
Linear. ActiveVideo Amplifiers and Modulators - Two (2) years
Linear slot diffusers shall be given by length stating the type and size. End caps for actual diffuser lengths and all necessary supports, hangers, metal brackets, suspension rods, and the like and protective painting or finishing shall be deemed to be included with the linear slot diffuser items.

Related to Linear

  • Linear Interpolation Where Linear Interpolation is specified as applicable in respect of an Interest Period in the applicable Final Terms, the Rate of Interest for such Interest Period shall be calculated by the Agent by straight line linear interpolation by reference to two rates based on the relevant Reference Rate (where Screen Rate Determination is specified as applicable in the applicable Final Terms) or the relevant Floating Rate Option (where ISDA Determination is specified as applicable in the applicable Final Terms), one of which shall be determined as if the Designated Maturity were the period of time for which rates are available next shorter than the length of the relevant Interest Period and the other of which shall be determined as if the Designated Maturity were the period of time for which rates are available next longer than the length of the relevant Interest Period provided however that if there is no rate available for a period of time next shorter or, as the case may be, next longer, then the Agent shall determine such rate at such time and by reference to such sources as it determines appropriate.

  • Speed The relative importance we attach is “high”.

  • Shift Rotation Routine shift rotation is not an approach to staffing endorsed by the Employer. Except for emergency situations where it may be necessary to provide safe patient care, shift rotation will not be utilized without mutual consent. If such an occasion should ever occur, volunteers will be sought first. If no one volunteers, the Employer will rotate shifts on an inverse seniority basis until the staff vacancies are filled.

  • Points A teacher with an evaluation rating of effective or highly effective will receive .67 points.  Any teacher having an evaluation result of “Improvement Necessary” or “Ineffective” will receive no raise.  Any teacher employed on less than a full time basis (1 FTE) shall receive compensation for the two factors of the compensation model on a pro-rated basis, in proportion to the percentage of one full time equivalent (1 FTE) for which the teacher is employed.  The base salaries of teachers is set forth in Appendix A.  The salary increase awarded to teachers using the performance factors set forth above will be added to their base salaries unless the teacher has reached the maximum base salary of $79,383. Those teachers who have reached this maximum base salary limit will receive the salary increase of $700.00 as a stipend. The amount of General Fund dollars available for teacher salary increase under the compensation model for 2017-2018 contract is $375,000.00. Compensation Model Example Step 1: Factors Used to Determine Salary Increase Factors Maximum Points Requirement

  • Rounding Any financial ratios required to be maintained by the Borrower pursuant to this Agreement shall be calculated by dividing the appropriate component by the other component, carrying the result to one place more than the number of places by which such ratio is expressed herein and rounding the result up or down to the nearest number (with a rounding-up if there is no nearest number).

  • Video This restriction includes, but is not limited to, use of the Beat and/or New Song in television, commercials, film/movies, theatrical works, video games, and in any other form on the Internet which is not expressly permitted herein.

  • Geometric visibility The visibility of the illuminating surface, including its visibility in areas which do not appear to be illuminated in the direction of observation considered, shall be ensured within a divergent space defined by generating lines based on the perimeter of the illuminating surface and forming an angle of not less than 5° with the axis of reference of the headlamp. The origin of the angles of geometric visibility is the perimeter of the projection of the illuminating surface on a transverse plane tangent to the foremost part of the lens of the headlamp.

  • Unbundled Channelization (Multiplexing) 5.7.1 To the extent NewPhone is purchasing DS1 or DS3 or STS-1 Dedicated Transport pursuant to this Agreement, Unbundled Channelization (UC) provides the optional multiplexing capability that will allow a DS1 (1.544 Mbps) or DS3 (44.736 Mbps) or STS-1 (51.84 Mbps) Network Elements to be multiplexed or channelized at a BellSouth central office. Channelization can be accomplished through the use of a multiplexer or a digital cross-connect system at the discretion of BellSouth. Once UC has been installed, NewPhone may request channel activation on a channelized facility and BellSouth shall connect the requested facilities via COCIs. The COCI must be compatible with the lower capacity facility and ordered with the lower capacity facility. This service is available as defined in NECA 4.

  • Signaling Each Party will provide the other Party with access to its databases and associated signaling necessary for the routing and completion of the other Party’s traffic in accordance with the provisions contained in the Unbundled Network Element Attachment or applicable access tariff.

  • Bilingual Differential When formally assigned in the employee’s position description, an employee assigned to interpret to or from another language to English will receive a differential of five percent (5%) of base pay.