S/T methodology and associated Sample Clauses

S/T methodology and associated work plan
Sample 1
AutoNDA by SimpleDocs
S/T methodology and associated work plan The NewProt efforts will all revolve around the protein engineering self-service portal, called SSP. The SSP will hold a large series of software, database, and information facilities. Table 1, to the left, lists a low-detail summary; details are provided in WP2-5. The SSP will be used for most dissemination activities, for the distribution of software and databases, and for all NewProt management activities. The SSP will include interactive workbench facilities. All facilities will become fully interoperable which will allow for easy to use yet powerful predictive and analytic protein engineering possibilities. The design of the SSP will get the highest priority in the first 12 months of the project. The ‘software and database partners’ will in the first 12 months prepare a comprehensive set of their own protein engineering software products for installation at or coupling to the SSP. They will work on the curation of commonly used, freely available databases and prepare these for installation (installation implies full integration and interoperability). The ‘experimental validation partners’ will in the first 12 months select a series of protein engineering (and chemical biology) targets that they will use for validation of the predictive capabilities of the available software packages, and they will set-up everything needed for engineering these proteins. After the initial 12 months the partners will run the iterative regime shown in figure 1.2.
Sample 1
S/T methodology and associated work plan The work plan is centred around technical development of key electric sail spacecraft components and augmented with analysis which enables one to plan concrete missions.
Sample 1
S/T methodology and associated work plan B 1.3.1. Overall strategy and general description The ANDES project will be organized to efficiently provide significant progress in all the steps of the nuclear data life cycle (measurements, evaluation, dissemination, validation, utilization and feedbacks), and to address a selected realistic number of the most important pending problems. Namely the main objective will be to improve the accuracy, prediction capability and the assessment of this accuracy for: the simulation of reactors (Gen III(+) and Gen IV) and fuel cycles based in the Uranium fuels; the simulation of advanced closed fuel cycles with multiple recycling; the modeling of high energy models valid for demonstrators as well as for the final industrial ADS. A particular effort will be devoted to a general improvement on the uncertainties and covariances and the way to use them. Following the type of activities and the coherence between teams, the activities will be organized into four technical work packages related with differential measurements, evaluation and uncertainties, integral validation and high energy models and experiments. The work package coordinators have been chosen for their known expertise in the field of their work package but also for their broad view on all the aspects of nuclear data. This will ensure a good management of the complementarities and the transfer of results between the different work packages. Taking into account that the dissemination and training activities, particularly the continuous information to the End-Users group, are the elements for a successful penetration of the new results and methods at present and their future improvements, the project includes an additional work package that will combine the management, dissemination, education and training activities.
Sample 1

Related to S/T methodology and associated

  • Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C.1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.

  • Grantee’s Notification of Change of Contact Person or Key Personnel The Grantee shall notify in writing their contract manager assigned within ten days of any change to the Grantee's Contact Person or Key Personnel.

  • Service Jointly Provisioned with an Independent Company or Competitive Local Exchange Company Areas 4.5.1 BellSouth will in some instances provision resold services in accordance with the General Subscriber Services Tariff and Private Line Tariffs jointly with an Independent Company or other Competitive Local Exchange Carrier.

  • Switching and Tagging Rules Each Party shall provide the other Parties a copy of its switching and tagging rules that are applicable to the other Parties’ activities. Such switching and tagging rules shall be developed on a non-discriminatory basis. The Parties shall comply with applicable switching and tagging rules, as amended from time to time, in obtaining clearances for work or for switching operations on equipment.

  • Employee Who Acts as Representative Where an employee wishes to represent at a meeting with the Employer, an employee who has presented a grievance, the Employer will, where operational requirements permit, grant leave with pay to the representative when the meeting is held in the headquarters area of such employee and leave without pay when the meeting is held outside the headquarters area of such employee.

  • Benefit Level Two Health Care Network Determination Issues regarding the health care networks for the 2017 insurance year shall be negotiated in accordance with the following procedures:

  • Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.

  • Particular Methods of Procurement of Consultants’ Services 1. Quality- and Cost-based Selection. Except as otherwise provided in paragraph 2 below, consultants’ services shall be procured under contracts awarded on the basis of Quality and Cost-based Selection.

  • Calculation methodology No adjustment in the Conversion Price need be made unless the adjustment would require an increase or decrease of at least 1% in the Conversion Price then in effect, provided that any adjustment that would otherwise be required to be made shall be carried forward and taken into account in any subsequent adjustment. Except as stated in this Article VI, the Conversion Rate will not be adjusted for the issuance of Common Stock or any securities convertible into or exchangeable for Common Stock or carrying the right to purchase any of the foregoing. Any adjustments that are made shall be carried forward and taken into account in any subsequent adjustment. All calculations under Article V and Section 6.06 hereof and this Section 6.07 shall be made to the nearest cent or to the nearest 1/10,000th of a share, as the case may be.

  • Notification of Disbursement Method Form Pursuant to the Project Agreement executed for this loan, there are two methods by which funds can be disbursed. The first method is for the Ohio Public Works Commission (OPWC) to pay vendors directly. The second method is for the Commission to reimburse the subdivision after project costs have been incurred and paid by the subdivision. For loans only, the OPWC needs to be formally notified in advance as to which method the subdivision plans to utilize. Please refer to the enclosure entitled "Notification of Disbursement Method" and the accompanying "Instructions for Declaring Official Intent". In deciding which method to use please consider the following: • Discuss your disbursement options and preferences with your Project Manager, Xxxxx Xxxxx, prior to making a selection. • Passing a Resolution of Intent for the entire loan amount doesn't do you any harm and can actually be beneficial in the event the Commission needs to reimburse the subdivision in the event of an overpayment. • At any point during the life of the project you can always have the OPWC pay contractors directly even if you have passed a Resolution. • If you need to pass a Resolution, we encourage subdivisions to do so as early as possible. At a minimum, a Resolution must be adopted no later than 60 days after the date of construction related project costs for which the subdivision will seek reimbursement from us.

Time is Money Join Law Insider Premium to draft better contracts faster.