Filter Fabric Sample Clauses

Filter Fabric. A. Geotextile Fabric shall be a nonwoven fabric consisting of continuous chain polymeric filaments or yarns of polyester, or polypropylene formed into a stable network by needle punching.
AutoNDA by SimpleDocs
Filter Fabric. Underdrain systems should utilize filter fabric or other means to prevent the soil from moving into and clogging perforated pipe.
Filter Fabric. Exfiltration trench systems should be designed so that aggregate in the trench is enclosed in filter fabric. This serves to prevent migration of fine materials from the surrounding soil that could result in clogging of the trench. Xxxxxxxxxx et al. (1991) reports that woven fabric (Mirafi 700XG) performed better in mixed sand and silty soil than non-woven fabric (Mirafi 140N). On the other hand, the 140N had higher exfiltration rates in xxxxx soils than the woven fabric. Filter fabric may also be utilized directly surrounding the perforated pipe. In this instance, sedimentation of particulates will occur in the perforated pipe. Consequently, the pipe is more prone to clogging and reductions in capacity will occur more often than usual. Xxxxxxxxxx et al. (1988) points out that while this may seem unacceptable, the pipe may be cleaned relatively easy using high pressure hoses, vacuum systems, etc. On the other hand, designs without the fabric directly surrounding the perforated pipe requires complete replacement when clogging occurs.
Filter Fabric. (a) Filter Fabric shall be woven geotextile material specifically designed for a silt fence application, meeting the following minimum requirements: Property Test Method Value Grab Tensile Strength ASTM D 4632 0.55 kN Grab Tensile Elongation ASTM D 4632 15% Xxxxxx Burst ASTM D 4786 2060 kPa Puncture ASTM D 4833 0285 kN Property Test Method Value Trapezoid Tear ASTM D 4533 0285 kN UV Resistance ASTM D 435 580%@500 hrs. Apparent Opening Size ASTM D 4751 0.60 mm Flow Rate ASTM D 4491 405 L/min/m² Acceptable Product: “Amoco 2130 Silt Fence Fabric” or approved equal in accordance with B7.
Filter Fabric. The filter shall be non-woven, polypropylene fabric with a maximum ACS of 212 pm (#70 U. S. Sieve), ASTM D 4751. The filter shall be capable of retaining fine silt size soil particles.

Related to Filter Fabric

  • FABRICATION Making up data or results and recording or reporting them.

  • Influenza Vaccine Upon recommendation of the Medical Officer of Health, all employees shall be required, on an annual basis to be vaccinated and or to take antiviral medication for influenza. If the costs of such medication are not covered by some other sources, the Employer will pay the cost for such medication. If the employee fails to take the required medication, she may be placed on an unpaid leave of absence during any influenza outbreak in the home until such time as the employee has been cleared by the public health or the Employer to return to the work environment. The only exception to this would be employees for whom taking the medication will result in the employee being physically ill to the extent that she cannot attend work. Upon written direction from the employee’s physician of such medical condition in consultation with the Employer’s physician, (if requested), the employee will be permitted to access their sick bank, if any, during any outbreak period. If there is a dispute between the physicians, the employee will be placed on unpaid leave. If the employee gets sick as a reaction to the drug and applies for WSIB the Employer will not oppose the application. If an employee is pregnant and her physician believes the pregnancy could be in jeopardy as a result of the influenza inoculation and/or the antiviral medication she shall be eligible for sick leave in circumstances where she is not allowed to attend at work as a result of an outbreak. This clause shall be interpreted in a manner consistent with the Ontario Human Rights Code.

  • Products Products available under this Contract are limited to Software, including Software as a Service, products and related products as specified in Appendix C, Pricing Index. Vendor may incorporate changes to their product offering; however, any changes must be within the scope of products awarded based on the posting described in Section 1.B above. Vendor may not add a manufacturer’s product line which was not included in the Vendor’s response to the solicitation described in Section 1.B above.

  • Raw Materials Lonza shall procure all required Raw Materials as well as consumables other than those Raw Materials that are Customer Materials. Customer shall be responsible for payment for all consumables and Raw Materials ordered or irrevocably committed to be procured by Lonza hereunder. Upon cancellation of any Batch or termination of the Agreement, all unused Raw Materials shall be paid for by Customer within [***] days of invoice and at Customer’s option will either be (a) held by Lonza for future use for the production of Product, (b) delivered to Customer, or (c) disposed of by Lonza.

  • Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.

  • API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Manufacture 2.1. The LED(s) on the LED module shall be equipped with suitable fixation elements.

  • RE-WEIGHING PRODUCT Deliveries are subject to re- weighing at the point of destination by the Authorized User. If shrinkage occurs which exceeds that normally allowable in the trade, the Authorized User shall have the option to require delivery of the difference in quantity or to reduce the payment accordingly. Such option shall be exercised in writing by the Authorized User.

  • OPTICAL ‌ The Employer agrees to provide Optical coverage for active full- time employees in the amount of one hundred twenty-five dollars ($125.00) every twenty-four (24) month period, for the cost of frames, lenses and the fitting of prescription glasses when recommended by a doctor or optometrist. Sunglasses or glasses for cosmetic purposes are not included nor is the cost of eye examinations. While this Appendix is intended to provide an overview of all benefit coverages the insurer’s plan documents will ultimately govern the administration of these benefits. RRSP‌ The Employer agrees to contribute the following amounts to a Registered Retirement Savings Plan for any full-time employee who agrees to contribute an equal amount as follows: Employer Employee Year 1 $550.00 $550.00 Year 2 $550.00 $550.00 Reflect yearly Employer and Employee contribution match. Such amounts shall be divided by the amount of pay periods for each year and shall be adjusted accordingly.

Time is Money Join Law Insider Premium to draft better contracts faster.