Extended Warranty - Longitudinal Joints Sample Clauses

Extended Warranty - Longitudinal Joints. Asphalt concrete mix shall be placed and compacted in accordance with the Department's Standard Specification, Division 4 Section 19 – End Product Specification (EPS). The provisions of Division 1, Section 4, Subsection 49.0 of the Department's Standard Specification shall be in effect for this Contract with the following exception. Longitudinal joints in the surface course of asphalt concrete paving shall be subject to the aforementioned Subsection 12.0 for a period of thirty six (36) months after satisfactory completion of the paving operation. Defects and omissions as referenced in Division 1, Section 4, Subsection 49.0 of the Department's Standard Specification shall include construction related defects, at or adjacent to the longitudinal joint, such as ravelling, segregation, de-bonding, pot holing or cracking. In the event that defect(s) are observed at or near the longitudinal joint, within 36 months, the Engineer will determine whether the defects are construction related. The Contractor shall repair at their own expense, all construction related defects as identified by the Engineer. Cracks up to 20mm wide shall be filled and sealed (no routing is required) in accordance with Division 4, Section 11 - Crack Filling and Crack Sealing (EPWS) of the Department's Standard Specification. Defects that cannot be repaired by crack filling and sealing shall be cold planed to a width of approximately 600mm and to the same depth of the surface course. Emulsified asphalt tack shall be applied to all joints and the underlying asphalt concrete. Asphalt concrete removed by cold planing shall be replaced with the equivalent type of asphalt concrete material according to the Department's Standard Specification, Division 4 Section 4 - Asphalt Concrete Hot Mixed - Hot Placed. The hot mix asphalt shall be compacted to 92.5% of the Maximum Theoretical Density (per ASTM D 3202) using both a rubber tired roller to obtain maximum compaction and a steel drum roller to obtain smoothness. Combination rollers are acceptable. The perimeter of the repaired area shall be sealed with a rubberized joint sealing material as specified in Division 4 Section 11.
Sample 1
AutoNDA by SimpleDocs

Related to Extended Warranty - Longitudinal Joints

  • Extended Warranty If the Quote includes an extended warranty, the extended warranty coverage period warranty will be for a 5-year term, which includes the hardware manufacturer’s warranty plus the 4-year extended term.

  • Warranty Period Except as may be otherwise specified or agreed, Contractor shall repair all defects in materials, equipment, or workmanship appearing within one year from the date of Substantial Completion of the Work. If Substantial Completion occurs by phase, then the warranty period for that the Work performed for each phase begins on the date of Substantial Completion of that phase, or as otherwise stipulated on the Certificate of Substantial Completion for the particular phase.

  • Warranty Periods All warranties begin to run from the date Material Completion is achieved.

  • Hardware Warranty A. RISK OF LOSS If you purchase any of the hardware Products directly from us, risk of loss or damage to hardware, will pass to you and acceptance will occur upon delivery to your “ship to” address or, if special shipping arrangements are agreed to, upon delivery to your carrier or designee. Title to hardware Products will pass from HPE to you upon full payment for or delivery of the Products, whichever is later. You agree to properly insure the Products for the benefit of HPE between the time risk of loss and damage pass and the time title passes.

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • Supplemental JBoss Software Conditions Software Access and Software Maintenance for Supplemental JBoss Software is intended and available for Development Purposes only and for up to 25 users for each 16 Core Band Subscription of Red Hat JBoss Middleware Software that you purchased. If you deploy or use the Supplemental JBoss Software for Production Purposes or for more than 25 users, you agree to purchase the appropriate Software Subscriptions for each Unit that you deploy or use. Red Hat’s Open Source Assurance Program applies only to the Red Hat JBoss Middleware Software Subscription that you purchased (such as Red Hat JBoss Enterprise Application Platform in the example above) and does not apply to Supplemental JBoss Software. JBoss xPaaS Subscriptions (defined below) are not considered Supplemental JBoss Software. Each installation and use of JBoss xPaaS Subscriptions Software for either Development Purposes or Production Purposes is a Unit and requires a paid Software Subscription.

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where InterGlobe has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to InterGlobe. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for InterGlobe (e.g. hairpinning):

  • Extended Support Services As long as funding is available (through FFFS, etc.), the district will provide the following supportive services for individuals who are eligible under the TANF Services 200% of poverty eligibility guidelines: Services listed in the supportive services attachment are provided to TANF, SNAP and 200% eligible individuals.

  • Compressed Work Week The Company and Union recognize the concept of the compressed work week. It is further understood that the compressed work week conditions will apply only to those departments that are on the compressed work week.

  • Loop Provisioning Involving IDLC 2.16.1 Where TWTC has requested an Unbundled Loop and AT&T uses IDLC systems to provide the local service to the customer and AT&T has a suitable alternate facility available, AT&T will make such alternative facilities available to TWTC. If a suitable alternative facility is not available, then to the extent it is technically feasible, AT&T will implement one of the following alternative arrangements for TWTC (e.g., hairpinning):

Time is Money Join Law Insider Premium to draft better contracts faster.