Minimum Requirements With respect to the Notes, the Issuers shall not have any obligations with respect to any underwriters or underwritten offering except a single underwritten offering of $270 million or more of Registrable Securities.
Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).
Listing and Maintenance Requirements Compliance The Company has not in the two years preceding the date hereof received written notice from any stock exchange, market or trading facility on which the Common Stock is or has been listed or quoted to the effect that the Company is not in compliance with the listing, maintenance or other requirements of such exchange, market, trading or quotation facility. The Company has no reason to believe that it does not now or will not in the future meet any such requirements.
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.
Compliance with Nasdaq Continued Listing Requirements The Company is in compliance with applicable Nasdaq continued listing requirements. There are no proceedings pending or, to the Company’s Knowledge, threatened against the Company relating to the continued listing of the Common Stock on Nasdaq and the Company has not received any notice of, nor to the Company’s Knowledge is there any reasonable basis for, the delisting of the Common Stock from Nasdaq.
Minimum Purchase Requirements Distributor shall make the minimum annual purchase of Products established in Exhibit B, unless the Agreement has become coexclusive. In the period within the fixed term and extension, if applicable, of the Agreement under Section 10(a) subsequent to [ * ], the parties shall meet in San Francisco at least [ * ] prior to the beginning of each of respective year to discuss market conditions and appropriate minimum purchases for such year. In the event that the parties fail to agree on an appropriate minimum any year subsequent to [ * ], the minimum annual purchase requirement for such year shall be calculated increasing or decreasing (as the case may be) the minimum purchase requirement for the preceding year in proportion to the increase or decrease in the [ * ] (based on data from mutually acceptable data provider) of the applicable product in the Territory. In the event Supplier is unable to deliver Products ordered by Distributor in an amount consistent with the most recent forecast, then the minimum annual purchase requirement shall be reduced by the quantity of Products that Supplier is unable to deliver when requested. In the event Distributor fails in any year (a “Shortfall Year”) to make the annual minimum purchase of Agreement Products required by Exhibit B, Supplier shall have the right to give Distributor written notice of default, and if such failure to make the minimum purchase is not cured (through the purchase of an amount of Agreement Product equal to the entire shortfall in the Shortfall Year, which amount shall not be counted towards any minimum purchase requirements for the year of purchase) within [ * ] of receipt of the notice, then Supplier shall have the right, in Supplier’s sole discretion and as Supplier’s sole remedy for Distributor’s failure to meet the minimum purchase requirements hereunder, either to convert the appointment of Distributor from exclusive to non-exclusive or to terminate this Agreement. In the event of either conversion to non-exclusive or termination of this Agreement pursuant to this Section 3(e), the Supplier shall pay Distributor a conversion fee equal to [ * ], and Distributor shall transfer all Regulatory Approvals relating to BMS or DES in the Territory to Supplier.
Technical Requirements All Corrections done by Customer, its Authorized Agent or a third party contractor must be performed in accordance with Boeing's applicable service manuals, bulletins or other written instructions, using parts and materials furnished or approved by Boeing.
Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.
Quality Requirements Supplier shall comply with Tesla’s quality requirements set forth in Attachment 6 entitled “Tesla Motors Supplier Handbook”.
Delivery Schedule The scheduled months of delivery of the Aircraft are listed in the attached Table 1. Exhibit B describes certain responsibilities for both Customer and Boeing in order to accomplish the delivery of the Aircraft.
