Remedial Actions Each Party shall notify the other immediately, and promptly confirm such notice in writing, if it obtains information indicating that any Product may be subject to any recall, corrective action or other regulatory action by any Governmental Authority or Regulatory Authority (as to TPTX’s notification obligation, only to the extent it would reasonably be expected to affect the Territory) (a “Remedial Action”). The Parties shall assist each other in gathering and evaluating such information as is necessary to determine the necessity of conducting a Remedial Action with respect to the Territory. Zai shall have sole discretion with respect to any matters relating to any Remedial Action in the Territory, including the decision to commence such Remedial Action and the control over such Remedial Action; provided that TPTX shall have sole discretion with respect to any matters relating to any Remedial Action in the Territory to the extent related to any Global Study. The cost and expenses of any Remedial Action in the Territory shall be borne solely by the Party with sole discretion; provided, however, that to the extent a Remedial Action in the Territory results primarily from the failure of the Product supplied by TPTX to comply with the Product Specifications, product warranties (as set forth in the Supply Agreement) or any Applicable Law, including cGMP requirements, then TPTX shall reimburse Zai for the reasonable cost and expense of such Remedial Action if this is required and after consultation with TPTX. Each Party shall, and shall ensure that its Affiliates and sublicensees shall, maintain adequate records to permit the Parties to trace the distribution and use of the Product in the Territory.
Primary Frequency Response Developer shall ensure the primary frequency response capability of its Large Generating Facility by installing, maintaining, and operating a functioning governor or equivalent controls. The term “functioning governor or equivalent controls” as used herein shall mean the required hardware and/or software that provides frequency responsive real power control with the ability to sense changes in system frequency and autonomously adjust the Large Generating Facility’s real power output in accordance with the droop and deadband parameters and in the direction needed to correct frequency deviations. Developer is required to install a governor or equivalent controls with the capability of operating: (1) with a maximum 5 percent droop ± 0.036 Hz deadband; or (2) in accordance with the relevant droop, deadband, and timely and sustained response settings from an approved Applicable Reliability Standard providing for equivalent or more stringent parameters. The droop characteristic shall be: (1) based on the nameplate capacity of the Large Generating Facility, and shall be linear in the range of frequencies between 59 and 61 Hz that are outside of the deadband parameter; or (2) based on an approved Applicable Reliability Standard providing for an equivalent or more stringent parameter. The deadband parameter shall be: the range of frequencies above and below nominal (60 Hz) in which the governor or equivalent controls is not expected to adjust the Large Generating Facility’s real power output in response to frequency deviations. The deadband shall be implemented: (1) without a step to the droop curve, that is, once the frequency deviation exceeds the deadband parameter, the expected change in the Large Generating Facility’s real power output in response to frequency deviations shall start from zero and then increase (for under-frequency deviations) or decrease (for over-frequency deviations) linearly in proportion to the magnitude of the frequency deviation; or (2) in accordance with an approved Applicable Reliability Standard providing for an equivalent or more stringent parameter. Developer shall notify NYISO that the primary frequency response capability of the Large Generating Facility has been tested and confirmed during commissioning. Once Developer has synchronized the Large Generating Facility with the New York State Transmission System, Developer shall operate the Large Generating Facility consistent with the provisions specified in Articles 9.5.5.1 and 9.5.5.2 of this Agreement. The primary frequency response requirements contained herein shall apply to both synchronous and non-synchronous Large Generating Facilities.
Reactive Power and Primary Frequency Response 9.6.1 Power Factor Design Criteria
Remedial Measures Upon becoming aware of an alleged security breach, Contractor’s Contract Manager must set up a conference call with the Department’s and the Customer’s Contract Manager. The conference call invitation must contain a brief description of the nature of the event. When possible, a thirty (30)- minute notice will be given to allow Department personnel to be available for the call. If the designated time is not practical for the Customer, an alternate time for the call will be scheduled. Contractor must share all available information on the call. The Contractor must answer all questions based on the information known at that time and answer additional questions as additional information becomes known. The Contractor must provide the Department and Customer with final documentation of the incident including all actions that took place. If the Contractor becomes aware of a security breach or security incident outside of normal business hours, the Contractor must notify the Department’s and the Customer’s Contract Manager and in all events, within one business day.
