Bollards Sample Clauses

Bollards. Adequate double bollards to be provided on the main deck distributed on the port and starboard side for effective mooring. The bollards placed in heavy foundations with a height of about 200 mm. Total height of the bollards 500 mm. Deck construction in way of bollards shall be reinforced with increased plating thickness and extra stiffeners.
AutoNDA by SimpleDocs
Bollards. The building(s) will be protected by the installation of crash barriers around the perimeter. These may be concrete bollards, planters, retractable gates, or other architectural features. They shall conform as much as practical to the existing building features and structures to avoid an armed camp appearance. SFO NO. DTSA20-03-R-00528 INITIALS: [SIG] & [SIG] --------- --------- 44 LESSOR GOV'T
Bollards. A. Pipe: Black Steel, ASTM A53, Type E, Grade A, Schedule 80, sized as shown, with 1/4-inch steel-plate cap welded all around and weld ground smooth
Bollards. Steel tubes for bollards shall conform to ASTM A 53 Grade A. Concrete shall conform to the requirements of Section 502. Paint for bollards shall conform to Section 714. Galvanized steel for bollards shall conform to Section 715.
Bollards. Construct and install bollards at location shown on plans. Fabricated bollards shall be inspected prior to installation. Final determination of bollard locations will be made in the field as directed. Excavate a hole for the bollard to the required depth. Assemble the bollard and set the bollard plumb. Place concrete for the bollard base according to Section 502. Galvanized posts shall be pre-treated with vinyl wash primer or per manufacturer’s recommendations prior to painting “OSHA” safety yellow.
Bollards. .1 The bollards are to be comprised of 150mm (6 in) diameter galvanized steel pipe;
Bollards. .1 There shall be one [1] bollard installed at the North corner and one [1] bollard installed at the East corner of the tower.
AutoNDA by SimpleDocs

Related to Bollards

  • Grade The employee's grade level. (1-15)

  • Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.212 – MARKET-RELATED CONTRACT TERM ADDITION (11/08). The term of this contract may be adjusted when a drastic reduction in wood product prices has occurred in accordance with 36 CFR 223.52. The Producer Price Index used to determine when a drastic reduction in price has occurred is stated in A20. Purchaser will be notified whenever the Chief determines that a drastic reduction in wood product prices has occurred. If the drastic reduction criteria specified in 36 CFR 223.52 are met for 2 consecutive calendar quarters, after contract award date, Contracting Officer will add 1 year to the contract term, upon Purchaser’s written request. For each additional consecutive quarter such a drastic reduction occurs, Contracting Officer will, upon written request, add an additional 3 months to the term during Normal Operating Season, except that no single 3-month addition shall extend the term of the contract by more than one year. Contracting Officer must receive Purchaser’s written request for a market-related contract term addition before the expiration of this contract. No more than 3 years shall be added to a contract's term by market-related contract term addition unless the following conditions are met:

  • Rubric The rubrics are a scoring tool used for the Educator’s self-assessment, the formative assessment, the formative evaluation and the summative evaluation. The districts may use either the rubrics provided by ESE or comparably rigorous and comprehensive rubrics developed or adopted by the district and reviewed by ESE.

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Dimensions Education: Bachelor’s or Master’s Degree in Computer Science, Information Systems, or other related field. Or equivalent work experience. Experience: A minimum of 10 years of IT (including Web/Internet, database applications and data warehousing) and business/industry work experience, with at least 3 years of leadership experience in managing multiple, large, cross-functional teams or project, and influencing senior level management and key stakeholders.

  • Weight The percent of the Base Price subject to adjustment based on an index change.

  • Scratches (Q) appliance malfunctions and any resultant leak there from; (R) any stain, soiling or damage resulting from everyday use or which has built up over time, e.g. hair, body or suntan oils and/or lotions; (S) signs of soiling include darkened areas where the body comes into contact with the furniture (these darkened areas are signs of soil build-up, which is not covered); (T) general maintenance and overall cleaning of the furniture is the consumer’s responsibility; (U) damage due to harsh or corrosive chemicals; (V) acids, including without limitation, dyes and inks (except ballpoint), plant food and fertilizer and bleach, gum; (W) any non-operating part or decorative parts such as hinges, knobs, handles, or shelves; (X) coverage under another insurance program; (Y) delivery and/or redelivery and/or loss or damage to the Covered Product while in the course of transit; (Z) design deficiency; (AA) fabrics with “X” cleaning codes and non-colorfast fabrics and leathers; (AB) odors; (AC) variation of the color, or graining of wood or wood products, marble or leather; (AD) split leathers used in seat cushions, back cushions or top or inside arm areas; (AE) natural markings on leather, such as, healed scars, insect bites, brand marks or wrinkles, or suede, and leathers with embossed patterns other than those stimulating natural cowhide; (AF) non- bovine leathers, and other buffed leathers; (AG) stains, color loss or damage resulting from cleaning methods or products (detergents, abrasives or other harsh cleaning agents) other than those recommended by the furniture manufacturer; (AH) stone or sand abrasion; (AI) loss or damage resulting from: pre-existing conditions known to You; (AJ) wear related issues, such as but not limited to, fading, wear, seam separation, stress tears, loss of foam resiliency, pilling or fraying of any fabric on all types of furniture; (AK) color loss or cracking and peeling on any leather or vinyl; (AL) splits or bi-cast leather; (AM) furniture that is used for commercial, institutional, outdoor or rental purposes; (AN) Customer’s Own Material furniture; (AO) wicker, rattan, and teakwood furniture; (AP) massage chairs; (AQ) stains or damage to suede, split-grain leather hide or exotic leathers; (AR) manufacturer quality issues such as stress tears, fabric flaws, fading, color loss or change, loss of foam or resiliency, cracking and peeling of leather or vinyl, natural leather markings, and defects in design and workmanship; (AS) Stains or damage that occur during assembly, delivery, installation, before furniture is delivered to your residence, while the furniture is located outside of your residence, while the furniture is in storage or being moved to or from storage or between residences; (AT) Wear & Tear caused by repeated use such as scuffing, soiling, hair/body oil, perspiration, surface abrasions, pilling or fraying of fabric, loose joints; (AU) Stains or damage covered under any manufacturer warranty, recall, homeowner, renter or other insurance policy; (AV) Stains or damage caused by structural problems, appliance malfunctions, Acts of God or natural disasters, theft, vandalism or illegal activity (AW) Stains or damage caused by independent contractors Specific to Home Automation: In additional to the exclusions listed above, this Agreement does not cover any loss, repairs or damage caused by or resulting from: (A) pre-existing conditions incurred or known to you (pre-existing means a condition prior to Plan issuance); (B) any repair covered by a manufacturer’s warranty or any insurance; (C) installation, or improper installation; or improper installation of customer replaceable components, modules, parts or peripherals; (D) damage or failure due to causes beyond our control such as environmental conditions, exposure to weather conditions or acts of nature including, but not limited to: fire, floods, smoke, sand, dirt, lightning, moisture, water damage, freezes, storms, wind, windstorm, hail, earthquake, animal or insect infestation, etc.; (E) damage or failure caused by riot, nuclear radiation, war, hostile action, or radioactive contamination, etc.; (F) battery failure or leakage; (G) collision, collapse, or explosion; (H) liquid spillage of any kind; (I) signal reception, transmission problems resulting from external causes, interruption of electrical service, loss of power, improper use of electrical/power, power “brown-out”, power overload or power surge (unless covered in the Special Features section of this document); (J) neglect, misuse, abuse, intentional damage, malicious mischief, theft, mysterious disappearance, vandalism or accidental damage; damage cause by dropping (K) rust, corrosion, warping, bending, etc.; (L) damage, warping, bending or rusting of any kind to the housing, cabinetry, outside casing or frame of the product; (M) any non-operating part, including but not limited to plastic, or decorative parts such as hinges, knobs, door liners, glass, handles, masks, rack rollers, shelves, etc.; (N) loss of or repair to components within the product not originally covered by the manufacturer’s warranty; (O) failure to product attachments not provided by the manufacturer or included in the original sale;

  • Grades At the end of each semester, students shall receive a final grade report that shall become a part of their permanent record. The College District’s grading system shall apply to all courses: A (90-100) - Excellent B (80-89) - Good C (70-79) - Average D (60-69) - Poor F (Below 60) - Failure I Incomplete Q Dropped W Dropped Due to Good Cause or Withdrawal from College CR Credit P Pass NP Not Passing FS Academic Fresh Start I - Incomplete: indicates that the coursework was incomplete because of serious illness or other justified emergency. The instructor shall change the grade of “I” to a grade based on the work completed for the course in addition to the work specified in the course completion contract. All incomplete work shall be completed within 90 days of the start of the next long semester. Failure to complete the work specified in the course completion contract shall result in a grade of zero, which shall be factored into the final grade calculation with appropriate weighting relative to other course grades.

  • Fuel 28.1 The Vehicle must be returned with the amount of fuel equal to that at the time of the commencement of the rental. If the Vehicle is returned with less fuel, the difference will be charged to You at a rate of $5.00 including GST per litre (which includes a service component).

  • Overbuilds Sprint will not provide non-discriminatory access to FTTH Loop or FTTC Loop on an unbundled basis when Sprint has deployed a FTTH Loop or FTTC Loop parallel to, or in replacement of, an existing loop facility, except that:

Time is Money Join Law Insider Premium to draft better contracts faster.