Ambient conditions Sample Clauses

Ambient conditions. 3.1.1. During the test, the test cell temperature shall be between 293 K and 303 K (20 °C and 30 °C). The absolute humidity (H) of either the air in the test cell or the intake air of the engine shall be such that:

Ambient conditions. 3.3.2.1. The ambient temperature shall be between 5 °C (278 K) and 35 °C (308 K) and the barometric pressure between 91 kPa and 104 kPa. The relative humidity shall be less than 95 %. 3.3.2.2. However, with the manufacturer's agreement, the tests may be made at lower ambient temperatures down to 1 °C. In this case the correction factor calculated for 5 °C should be used.

Ambient conditions. 2.1.3.1. Ambient condition indoor

Ambient conditions. The test shall be conducted under the ambient conditions laid down in this section. The ambient conditions become ‘extended’ when at least one of the temperature or altitude conditions is extended. The factor for extended conditions as defined in paragraph 10.5. shall only be applied once even if both conditions are extended in the same time period. Notwithstanding the opening 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6 – Annex 3, ▇▇▇▇▇://▇▇▇▇▇.▇▇▇/transport/standards/transport/vehicle-regulations-wp29/resolutions. paragraph of this section, if a part of the test or the entire test is performed outside of extended conditions, the test shall be invalid only when final emissions as calculated in Annex 11, are greater than the applicable emission limits. The conditions are as follows: Moderate altitude conditions Altitude lower or equal to 700 meters above sea level. Extended altitude conditions Altitude higher than 700 meters above sea level and lower or equal to 1300 meters above sea level. Moderate temperature conditions Greater than or equal to 273.15 K (0 °C) and lower than or equal to 308.15 K (35 °C). Extended temperature conditions Greater than or equal to 266.15 K (– 7 °C) and lower than 273.15 K (0 °C) or greater than308.15 K (35 °C) and lower than or equal to311.15 K (38 °C).

Ambient conditions. All pipes, materials and equipment shall be in every respect suitable for storage, installation, use and operation in the conditions of temperature, humidity and The PH and water quality appertaining in Jordan. Atmospheric temperature in Jordan varies between -10˚C and 50 ˚C.

Ambient conditions. Each Plant shall be designed and constructed to take account of the following ambient conditions:

Ambient conditions. 1 Temperature, Humidity and Substrate Moisture Content Levels: .1 Unless specifically pre-approved by specifying body, Paint Inspection Agency and, applied product manufacturer. .2 Do not perform repainting work when: .1 Ambient air and substrate temperatures are below 5 degrees C. .2 Substrate temperature is over 32 degrees C unless paint is specifically formulated for application at high temperatures. .3 Substrate and ambient air temperatures are expected to fall outside MPI or paint manufacturer's prescribed limits.

Ambient conditions. Unless Lender grants special permission in writing for outdoor exhibition, College must protect Exhibit at all times against direct sunlight, rain, excessive humidity and excessively dry conditions. In addition, College properly must protect all watercolors, drawings, prints, fabrics and photographs from fading damage due to exposure to direct or reflected sunlight and strong artificial light, fluorescent light or proximity to heat sources.

Ambient conditions. Paint shall be applied only to surfaces that are above the dew point temperature and that are completely free of moisture as determined by sight and touch. Paint shall not be applied to surfaces upon which there is detectable frost or ice. Except as otherwise specified, the temperature of the surfaces to be painted and of air in contact therewith shall be not less than 45 degrees F during paint application nor shall paint be applied if the surfaces can be expected to drop to 32 degrees F or lower before the film has dried to a reasonably firm condition. During periods of inclement weather, painting may be continued by enclosing the surfaces and applying artificial heat, provided the minimum temperatures and surface dryness requirements prescribed previously are maintained. Paint shall not be applied to surfaces heated by direct sunlight or other sources to temperatures that will cause detrimental blistering, pinholing, or porosity of the film.