SHOP TEMPERATURE Sample Clauses

SHOP TEMPERATURE. With the cooperation of employees, the Company will attempt to maintain shop temperature above 50 degrees Fahrenheit (10 degrees Celsius), during cold weather. The Company agrees not to require its employees to perform outside repair work in temperatures below -20 degrees Fahrenheit (-29 degrees Celsius), unless adequate protection and some form of heat is provided. Tarpaulins, windbreaks, etc., shall be erected before commencement of work and heat must be made available.
Sample 1Sample 2Sample 3See All (13)
AutoNDA by SimpleDocs
SHOP TEMPERATURE. With the co-operation of employees, the Company will attempt to maintain shop temperatures above 16°C during cold weather. The Company agrees not to require its employees to perform outside repair work in temperatures below -29°C, unless adequate protection and some form of heat is provided. Tarpaulins, windbreaks, etc., shall be erected before commencement of work and heat must be made available. The Company shall supply protective clothing when employees are engaged in cleaning equipment.
Sample 1Sample 2Sample 3See All (8)
SHOP TEMPERATURE. With the cooperation of employees, the Company will attempt to maintain comfortable shop temperatures during cold weather. When performing repair work outside in severe winter conditions and the length of the job warrants protection, protection and/or heat will be provided where practical.
Sample 1Sample 2Sample 3See All (4)

Related to SHOP TEMPERATURE

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Signaling Parameters All SS7 signaling parameters will be provided in conjunction with traffic exchange trunk groups, where and as available. These parameters include Automatic Number Identification ("ANI"), Calling Party Number ("CPN"), Privacy Indicator, calling party category information, originating line information, charge number, etc. Also included are all parameters relating to network signaling information, such as Carrier Information Parameter ("CIP"), wherever such information is needed for call routing or billing. GTE will provide SS7 via GR-394-SS7 and/or GR-317-SS7 format(s).

  • Illumination The Engineer shall refer to TxDOT’s Highway Illumination Manual and other deemed necessary State approved manuals for design of continuous lighting and safety lighting for all conventional, high-mast, and underpass lighting. The Engineer shall include safety lighting as part of each design on each flashing beacon and traffic signal. The Engineer shall provide a preliminary layout for initial review and approval by the State. The Engineer shall prepare circuit wiring diagrams showing the number of luminaries on each circuit, electrical conductors, length of runs, service pole assemblies. Underpass lighting must be used on all structures within each project. The Engineer shall integrate existing illumination within the project limits into the proposed design. The Engineer shall coordinate with the State to determine the location of proposed high- mast, conventional, and underpass lighting.

  • Staging In addition to the staging categories listed in paragraph 1 of Annex 2-A, this Schedule contains staging categories 20-A, 20-B, PR-1 and PR-130:

  • Outputs 11. The objectives and outcomes of this Agreement will be achieved by:

  • Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.

  • Tolerances 1. If a non-originating material used in the production of a product does not satisfy the requirements set out in Annex 3-B, the product shall be considered as originating in a Party, provided that:

  • Technical Specification As enumerated in Special Conditions of Contract/Scope of Work/attached Drawing/ Details/Schedule of Rates.

  • Workloads (a) The parties agree that patient care is enhanced if concerns relating to professional practice, patient acuity, fluctuating Work-Loads and fluctuating staffing are resolved in a timely and effective manner.

Time is Money Join Law Insider Premium to draft better contracts faster.