Setting the Various Parameters Sample Clauses

Setting the Various Parameters. ‌ The functions of the Cutting Plotter Controller are explained according to each parameter. When the Controller is launched, the following screen appears. Note: The screen above is the screen that is displayed when an FC7000 Series cutting plotter has been connected. Use Plotter Settings/Use Controller Settings .......... Selects whether to use the settings made at the plotter or to use the Controller settings for the cutting conditions (Blade (Pen Type), Force, Speed, Quality, Offset). If “Use Controller Settings” is selected COND. No. [9] is displayed on the plotter's LCD. The Controller settings will be made according to the conditions specified for COND. No. [9]. If “Use Plotter Settings” is selected The Controller's cutting condition settings will become invalid. Note: If ROBO Master-Pro was used to launch the Controller, the setting is fixed to “Use Controller Settings” and cannot be changed. Media Type To enable easy specification of cutting conditions, the most suitable cutting conditions for each media type are stored in the Cutting Plotter Controller as separate files, with the media type used as the file name. • File name: Fluorescent film A (The following settings are stored under the file name [Fluorescent film A] ) • Blade Selection (Pen Type) : CB09UA • Force : 20 • Speed : 10 • Quality : 1 • Offset : 0 Files with the most standard settings are installed together with the Cutting Plotter Controller. The settings file name selected from the pull-down list is displayed for “Media Type”, and the contents of that file are displayed underneath the selected file name. If you change your selection, the displayed settings will also change. The plotter settings will also be changed at the same time. List Edit Click this button to display the [Edit Condition List] window that enables you to edit and manage settings files. In this window you can create new files, change file contents, and use the delete and copy functions. Note: For further details on the [Edit Condition List] window, refer to Section 2.3, "Edit Condition List". Test Performs test cutting using the currently displayed cutting conditions in order to check the cutting quality. Move the cutter pen to the position where you wish to perform test cutting, and then click the [Test] button to cut a 1 cm x 1 cm test pattern. Note: Check the cutting results. If the film is cut cleanly, and there are faint traces on the backing sheet, the cutting conditions are correct. If cutting has not been p...
Sample 1
AutoNDA by SimpleDocs
Setting the Various Parameters. ‌ The functions of the Cutting Plotter Controller are explained according to each parameter. When the Controller is launched, the following screen appears. Note: The screen above is the screen that is displayed when an FC7000 Series cutting plotter has been connected. Use Plotter Settings/Use Controller Settings ............ Selects whether to use the settings made at the plotter or to use the Controller settings for the cutting conditions (Blade (Pen Type), Force, Speed, Quality, Offset). If "Use Controller Settings" is selected COND. No. [9] is displayed on the plotter's LCD. The Controller settings will be made according to the conditions specified for COND. No. [9].
Sample 1

Related to Setting the Various Parameters

  • Changes to these Terms and Conditions Reserving the right to change these terms and conditions. We reserve the right to change or add to these terms and conditions from time to time for legal, safety or other substantive reasons or in order to assist the proper delivery of education at the School. The School will send you notice of any such modifications prior to the end of the penultimate term before the modifications are to take effect.

  • Changes to the Terms and Conditions We may update or amend these terms and conditions (including our Fees & Limits Schedule). Notice of any changes will be given on our website, or by e-mail notification, or by SMS at least 2 months in advance. By continuing to use the Payment Services after the expiry of the 2-month notice period you acknowledge that you indicate your acceptance to be bound by the updated or amended terms and conditions. If you do not wish to be bound by them, you should stop using the Payment Services and terminate this Agreement in accordance with Clause 10 before the changes take effect.

  • CLOUD SPECIFIC TERMS AND CONDITIONS To the extent that Contractor has received an award for Lot 3, Cloud, the following terms and conditions apply to Lot 3, Cloud. For the duration of an Authorized User Agreement, the Cloud Solution shall conform to the Cloud Solution Manufacturer’s specifications, Documentation, performance standards (including applicable license duration, warranties, guarantees, Service Level Agreements, service commitments, and credits). PROTECTION OF DATA, INFRASTRUCTURE AND SOFTWARE Contractor is responsible for providing physical and logical security for all Data, infrastructure (e.g. hardware, networking components, physical devices), and software related to the services the Contractor is providing under the Authorized User Agreement. All Data security provisions agreed to by the Authorized User and Contractor within the Authorized User Agreement may not be diminished for the duration of the Authorized User Agreement without prior written agreement by the parties amending the Authorized User Agreement.

  • Changes to this Agreement We may make changes to this Agreement from time to time on the basis that you are able to end the Agreement without charge by us.

  • CHANGES TO THE ORIGINAL LEARNING AGREEMENT The section to be completed during the mobility is needed only if changes have to be introduced into the original Learning Agreement. In that case, the section to be completed before the mobility should be kept unchanged and changes should be described in this section. When changes to the mobility programme arise, they should be agreed as soon as possible with the sending institution. In case the change concerns an extension of the duration of the mobility programme abroad, the request can be made by the trainee at the latest one month before the foreseen end date. All parties must confirm that the proposed amendments to the Learning Agreement are approved. For this specific section, original or scanned signatures are not mandatory and an approval by email may be enough. The procedure has to be decided by the sending institution, depending on the national legislation.

  • Additional Donor Terms and Conditions The Donor Terms (if any) are incorporated in this Agreement by reference and are fully binding on Contractor and Mercy Corps. In the event of a conflict between the Donor Terms and any other provision of this Agreement (including any Additional Terms of TO) or any other document between Contractor and Mercy Corps, the Donor Terms will prevail.

  • SPECIFIC TERMS AND CONDITIONS To the extent that Contractor has received an award for Lot 4, Implementation Services, the following terms and conditions apply to Lot 4 Implementation Services. All Services covered under Lot 4 – Implementation Services must be performed within CONUS. REQUEST FOR QUOTATION (RFQ) TRANSACTION PROCESS An RFQ for this Lot will be awarded based on, and result in, a deliverable-based Statement of Work (SOW) which will be incorporated into an Authorized User Agreement. The RFQ will include but is not limited to: Authorized User timeframes; system integration requirements; and other risks that may affect the cost to the Authorized User. All responses to RFQs must include detailed price information, including but not limited to: hours required per title, cost per hour, etc. Travel, lodging and per diem costs must be itemized in the total quote and may not exceed the rates in the NYS OSC Travel Policy. More information can be found at xxxx://xxx.xxx.xxxxx.xx.xx/agencies/travel/travel.htm. All costs must be itemized and included in the Contractor’s quote. PARTICIPATION OPPORTUNITIES FOR NEW YORK STATE CERTIFIED SERVICE- DISABLED VETERAN OWNED BUSINESSES Article 17-B of the New York State Executive Law provides for more meaningful participation in public procurement by certified Service-Disabled Veteran-Owned Businesses (“SDVOB”), thereby further integrating such businesses into New York State’s economy. OGS recognizes the need to promote the employment of service-disabled veterans and to ensure that certified service-disabled veteran-owned businesses have opportunities for maximum feasible participation in the performance of OGS contracts. In recognition of the service and sacrifices made by service-disabled veterans and in recognition of their economic activity in doing business in New York State, Bidders are expected to consider SDVOBs in the fulfillment of the requirements of the Contract. Such participation may be as subcontractors or suppliers, as protégés, or in other partnering or supporting roles.

  • Changes to the Terms of Use We may revise and update these Terms of Use from time to time in our sole discretion. All changes are effective immediately when we post them, and apply to all access to and use of the Website thereafter. Your continued use of the Website following the posting of revised Terms of Use means that you accept and agree to the changes. You are expected to check this page from time to time so you are aware of any changes, as they are binding on you.

  • ACCEPTANCE OF THE TERMS AND CONDITIONS 3.1 Before applying to PCUL’s products on our system, you should first carefully read and understand these Terms and Conditions which will govern the use and operation of our system and the products and services accessible thereof;

  • Changes to Terms and Conditions A. The February 2014 version of the DoD FAR Supplement 252.227-7013 and 252.227- 7014 clauses apply to this Order.

Time is Money Join Law Insider Premium to draft better contracts faster.