Legal Action; Utilization of Special Receivership Powers The Assuming Institution shall notify the Receiver in writing (such notice to be given in accordance with Article V below and to include all relevant details) prior to utilizing in any legal action any special legal power or right which the Assuming Institution derives as a result of having acquired an asset from the Receiver, and the Assuming Institution shall not utilize any such power unless the Receiver shall have consented in writing to the proposed usage. The Receiver shall have the right to direct such proposed usage by the Assuming Institution and the Assuming Institution shall comply in all respects with such direction. Upon request of the Receiver, the Assuming Institution will advise the Receiver as to the status of any such legal action. The Assuming Institution shall immediately notify the Receiver of any judgment in litigation involving any of the aforesaid special powers or rights.
CONSTRUCTION MANAGER’S RESPONSIBILITIES The Construction Manager’s Preconstruction Phase responsibilities are set forth in Sections 2.1 and 2.2. The Construction Manager’s Construction Phase responsibilities are set forth in Section 2.3. The Owner and Construction Manager may agree, in consultation with the Architect, for the Construction Phase to commence prior to completion of the Preconstruction Phase, in which case, both phases will proceed concurrently. The Construction Manager shall identify a representative authorized to act on behalf of the Construction Manager with respect to the Project.
CONSTRUCTION MANAGER’S SERVICES The services which the Construction Manager shall provide include, but are not limited to, those described or specified herein. The services described or specified shall not be deemed to constitute a comprehensive specification having the effect of excluding services not specifically mentioned.
Enterprise Information Management Standards Grantee shall conform to HHS standards for data management as described by the policies of the HHS Office of Data, Analytics, and Performance. These include, but are not limited to, standards for documentation and communication of data models, metadata, and other data definition methods that are required by HHS for ongoing data governance, strategic portfolio analysis, interoperability planning, and valuation of HHS System data assets.
RECORDS MANAGEMENT AND MAINTENANCE 35 A. CONTRACTOR, its officers, agents, employees and subcontractors shall, throughout the term 36 of this Agreement, prepare, maintain and manage records appropriate to the services provided and in 37 accordance with this Agreement and all applicable requirements.
Level of Supervision Supervision is generally present to establish general objectives relative to a specific project, to outline the desired end product and to identify potential resources for assistance. Some positions will require routine supervision to general direction depending upon experience and the complexity of the tasks. Some positions will require general direction. May supervise or co-ordinate others to achieve objectives, including liaison with employees at higher levels. May undertake stand-alone work.
Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract.
State of New York Executive Department Office of General Services Procurement Services Corning Tower - 00xx Xxxxx Xxxxxx Xxxxx Xxxxx Xxxxxx, XX 00000 THIS CONTRACT (hereinafter “Contract” or “Centralized Contract”) for the acquisition of Project Based Information Technology Consulting Services is made between the People of the State of New York, acting by and through the Commissioner of the Office of General Services (hereinafter “State” or “OGS”) whose principal place of business is the 41st Floor, Corning Tower, The Governor Xxxxxx X. Xxxxxxxxxxx Empire Xxxxx Xxxxx, Xxxxxx, Xxx Xxxx 00000, pursuant to authority granted under New York State Finance Law §163, and SVAM INTERNATIONAL, INC. (hereinafter “Contractor”), with its principal place of business at 000 Xxxx Xxxxx Xxxx, Xxxxx 000, Xxxxx Xxxx, XX 00000. The foregoing are collectively referred to as the “Parties.”
Other Controller Audit Any other Controller may audit SAP’s control environment and security practices relevant to Personal Data processed by SAP in line with Section 5.1 only if any of the cases set out in Section 5.1 applies to such other Controller. Such audit must be undertaken through and by Customer as set out in Section 5.1 unless the audit must be undertaken by the other Controller itself under Data Protection Law. If several Controllers whose Personal Data is processed by SAP on the basis of the Agreement require an audit, Customer shall use all reasonable means to combine the audits and to avoid multiple audits.
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
