American Welding Society Sample Clauses

American Welding Society. (AWS D1.3) Light Gauge Metal (includes butt and plug weld).................................................................................................. Procedure Qualification per AWS, ASME or Military Standards.......................................................................................... Fillet Weld Test (Break and Etch Test)........................................................................................................................................
AutoNDA by SimpleDocs
American Welding Society. 1. AWS A2.4 - Standard Symbols for Welding, Brazing, and Nondestructive Examination.
American Welding Society. Club Advisor - $2,476 Responsible for the overall supervision of welding students participating in the AWN local chapter. Promote the values and goals of the organization, attend offsite meetings and supervise students participating in competitive events for the organization. Participate in/or organize a community service project.
American Welding Society. 1. AWS D1.1 – Structural Welding Code – Steel.

Related to American Welding Society

  • Geotechnical Engineer « »« » « » « » « » « »

  • Office of Inspector General Investigative Findings Expert Review In accordance with Senate Bill 799, Acts 2021, 87th Leg., R.S., if Texas Government Code, Section 531.102(m-1)(2) is applicable to this Contract, Contractor affirms that it possesses the necessary occupational licenses and experience.

  • Value Engineering The Supplier may prepare, at its own cost, a value engineering proposal at any time during the performance of the contract. The value engineering proposal shall, at a minimum, include the following;

  • Standards for Determining Commercial Reasonableness Borrower and Silicon agree that a sale or other disposition (collectively, "sale") of any Collateral which complies with the following standards will conclusively be deemed to be commercially reasonable: (i) Notice of the sale is given to Borrower at least seven days prior to the sale, and, in the case of a public sale, notice of the sale is published at least seven days before the sale in a newspaper of general circulation in the county where the sale is to be conducted; (ii) Notice of the sale describes the collateral in general, non-specific terms; (iii) The sale is conducted at a place designated by Silicon, with or without the Collateral being present; (iv) The sale commences at any time between 8:00 a.m. and 6:00 p.m; (v) Payment of the purchase price in cash or by cashier's check or wire transfer is required; (vi) With respect to any sale of any of the Collateral, Silicon may (but is not obligated to) direct any prospective purchaser to ascertain directly from Borrower any and all information concerning the same. Silicon shall be free to employ other methods of noticing and selling the Collateral, in its discretion, if they are commercially reasonable.

  • Reverse Engineering The Customer must not reverse assemble or reverse compile or directly or indirectly allow or cause a third party to reverse assemble or reverse compile the whole or any part of the software or any products supplied as a part of the Licensed System.

  • Supervisors Working (a) The work of Supervisors will not include assignment to work normally performed by employees of the bargaining unit except for training or demonstration. “Training or demonstration” shall not be used as a subterfuge for the performing of any bargaining unit work. Any claimed abuses will be referred to the Grievance Procedure. Where possible, the shop xxxxxxx will be notified. Supervisors will not perform bargaining unit work until after all rea- sonable efforts have been exhausted to have the work covered.

  • Architect/Engineer (A/E) means a person registered as an architect pursuant to Tex. Occ. Code Xxx., Chapter 1051, as a landscape architect pursuant to Tex. Occ. Code Xxx., Chapter 1052, a person licensed as a professional engineer pursuant to Tex. Occ. Code Xxx., Chapter 1001 and/or a firm employed by Owner or a design-build contractor to provide professional architectural or engineering services and to exercise overall responsibility for the design of a Project or a significant portion thereof, and to perform the contract administration responsibilities set forth in the Contract.

  • Programme Management The Government will establish a programme management office and the Council will be able to access funding support to participate in the reform process. The Government will provide further guidance on the approach to programme support, central and regional support functions and activities and criteria for determining eligibility for funding support. This guidance will also include the specifics of any information required to progress the reform that may be related to asset quality, asset value, costs, and funding arrangements.

  • Professional Engineering and Architect’s Services Professional Engineering and Architect’s Services are not permitted to be provided under this Agreement. Texas statutes prohibit the procurement of Professional Engineering and Architect’s Services through a cooperative agreement.

  • Synchronization, Commissioning and Commercial Operation 4.1.1 The Power Producer shall give at least thirty (30) days written notice to the SLDC and GUVNL, of the date on which it intends to synchronize the Power Project to the Grid System.

Time is Money Join Law Insider Premium to draft better contracts faster.