Scan time definition

Scan time means the period of time between the beginning and end of x-ray transmission data accumulation for a single scan.
Sample 1Sample 2Sample 3
Scan time means the time elapsed during the accumulation of x-ray transmission data for a single scan.
Sample 1Sample 2Sample 3
Scan time means the time elapsed during the accumulation of x-ray transmission data for a single scan. "Scattered radiation" means radiation that, during passage through matter, has been deviated in direction (See "Direct scattered radiation").
Sample 1Sample 2Sample 3

Examples of Scan time in a sentence

  • The Composite Scan time for a Trusted System represents the time required to read the input data, solve the application logic, and write the output data.

  • Scan time limit for a single file (seconds) - For some very large files, the scanning time may be relatively long.

  • Image Scan time should be in range of 6 to 40 Seconds (Depends on type of scan).

  • Module begins to read when receive scan command from mainframe( bit0 of zone bit 0x0002 writes”1”) , and stop at output or read timeout.Command triggered modeUnder command triggered mode, command for serial port trigger is 7E 00 08 01 00 02 01 AB CD;After receiving command, model will output “ 02 00 00 01 00 33 31” and start scan.Time settlement for single readRead and Scan time before output.

  • Scan time was 1 sec; tube current, 275 mA; and voltage, 137 kVp. Scans were reconstructed using a high-spatial-frequency algorithm, and window width and level were 1300 and 650 HU, respectively.Dependent opacity was visually estimated by two radiol- ogists (K.N.L, S.K.Y) who reviewed cases in random order and were blinded to the percent of vital capacity at which the scan was obtained (Table 1).

  • Scan time was 3:21 min for imaging the whole phantom (either agarose or urine) or the stack of pig kidneys in the plastic container.

  • Scan time and patient dose for thoracic imaging in neonates and small children using axial volumetric 320-detector row CT compared to helical 64-, 32-, and 16- detector row CT acquisitions.

  • Scan time for a closed loop shall be the cycle time taken by controller to read and process input, perform control calculations and update controller output for loops configured within controllers.

  • Making Bookings (Bookings by email) Scan time is booked via NeuRA Imaging Reception.

  • Parameter Single-energy CT Dual-energy CT kVp 120 80/140 dual Tube current (mA) 300 375 Scan time (s) 0.5 0.6 Pitch 0.984:1 0.984:1 Collimation (mm) 40 40 Image acquisition (mm) 64 × 0.625 64 × 0.625 Scan field of view Body large (50 cm) Body large (50 cm) Kernel ‘‘Bone’’ ‘‘Detail’’ ASIR 30% Not available CTDIvol (mGy) 11.35 12.92 ASIR, adaptive statistical iterative reconstruction; CTDIvol, volumetric CT dose index.


More Definitions of Scan time

Scan time means the period of time between the beginning and end of X-ray transmission data
Sample 1Sample 2Sample 3
Scan time means the periods of time between the beginning and end of x-ray transmission data accumulation for asingle scan.
Sample 1Sample 2
Scan time means the periods of time between the beginning and end of x-ray transmission data accumulation for a single scan. "Scattered radiation" means radiation that, during passage through matter, has been deviated in direction. (See definition
Sample 1
Scan time means the time elapsed during the accumlation of x-ray transmission
Sample 1
Scan time means the period of time between the beginning
Sample 1
Scan time means the timeelapsed during the accumlation of x-ray transmission data for a single scan.*/
Sample 1

Related to Scan time

  • Real-time means the actual time during which a process or event occurs.

  • Local Time means (a) with respect to a Loan or Borrowing denominated in Dollars, New York City time and (b) with respect to a Loan or Borrowing denominated in any Foreign Currency, London time.

  • Double time means twice the straight-time rate.

  • Valuation Time means the close of business in the city of the Valuation Agent on the Local Business Day before the Valuation Date or date of calculation, as applicable, provided that the calculations of Value and Exposure will be made as of approximately the same time on the same date.

  • Applicable Time means, with respect to any borrowings and payments in any Alternative Currency, the local time in the place of settlement for such Alternative Currency as may be determined by the Administrative Agent or the applicable L/C Issuer, as the case may be, to be necessary for timely settlement on the relevant date in accordance with normal banking procedures in the place of payment.

  • Execution Time means the date and time that this Agreement is executed and delivered by the parties hereto.

  • Trading Day means a day on which the principal Trading Market is open for trading.

  • Quotation Date means, in relation to any Interest Period (or any other period for which an interest rate is to be determined under any provision of a Finance Document), the day on which quotations would ordinarily be given by leading banks in the London Interbank Market for deposits in the currency in relation to which such rate is to be determined for delivery on the first day of that Interest Period or other period;