SLASH TREATMENT Subdivision or Unit No Sample Clauses

SLASH TREATMENT Subdivision or Unit No. Specified Method Maximum Height of Decks Landings ALL MACH/DECK 15’ Disposal Sites N/A N/A N/A
Sample 1Sample 2See All (5)
AutoNDA by SimpleDocs
SLASH TREATMENT Subdivision or Unit No. Specified Method Maximum Height of Decks Landings ALL MACH – Machine Pile landing slash 12 FEET Disposal Sites N/A N/A N/A TREATMENT ALONG PERMANENT ROADS Permanent roads that require roadside slash treatment are listed in the attached table and shown on Contract Area Map. All Logging and Construction Slash within Required Disposal Strips shall be treated by Contractor. "Required Disposal Strips" are those areas adjacent to permanent roads where slash treatment is required for resource objectives. The width of Required Disposal Strips is shown in the attached table and is measured in slope distance from Roadbed edges of permanent roads. By agreement, in Clearcutting Units and regeneration units slash from Required Disposal Strips may be treated with other Logging Slash. By agreement the location of Required Disposal Strips may be adjusted from side to side without materially changing the total work required. Slash treatment in Required Disposal Strips shall be accomplished without affecting the proper functioning of channels leading to and from drainage structures. Logging Slash larger than treatment size requirements of the specified method shall either be Scattered outside Required Disposal Strip, within Required Disposal Strip or Decked at agreed locations as shown in the attached table. SLASH TREATMENT Road No. Subdivision and/ or Unit No. or Road Juncitons (From To) Width of Required Disposal Strip Specified Method Slash Larger Than Treatment Size Requirements of Specified Method N/A SAMPLE TREATMENT ALONG TEMPORARY ROADS. Outside of Clearcutting Units or regeneration units, all trees felled or pushed over and trees damaged beyond recovery by Temporary Road construction shall be felled, limbed to a stem d.o.b. of approximately 3 inches, at which point the top shall be cut from the remainder of the stem, and stem shall be bucked into lengths not exceeding 20 feet. Such slash shall be Scattered free of soil to reduce concentrations unless treatment is required by another specified method.
Sample 1Sample 2See All (4)
SLASH TREATMENT Subdivision or Unit No. Specified Method Maximum Height of Decks Landings All STACK, DECK, MACH 20 Disposal Sites All STACK, DECK, MACH 20 TREATMENT ALONG PERMANENT ROADS Permanent roads that require roadside slash treatment are listed in the attached table and shown on Contract Area Map. All Logging and Construction Slash within Required Disposal Strips shall be treated by Contractor. "Required Disposal Strips" are those areas adjacent to permanent roads where slash treatment is required for resource objectives. The width of Required Disposal Strips is shown in the attached table and is measured in slope distance from Roadbed edges of permanent roads. By agreement, in Clearcutting Units and regeneration units slash from Required Disposal Strips may be treated with other Logging Slash. By agreement the location of Required Disposal Strips may be adjusted from side to side without materially changing the total work required. Slash treatment in Required Disposal Strips shall be accomplished without affecting the proper functioning of channels leading to and from drainage structures. Logging Slash larger than treatment size requirements of the specified method shall either be Scattered outside Required Disposal Strip, within Required Disposal Strip or Decked at agreed locations as shown in the attached table.
Sample 1Sample 2
SLASH TREATMENT Subdivision or Unit No. Specified Method Maximum Height of Decks Landings All MACH – machine piling landing slash 12 feet All COVER – cover landing slash piles X/X Xxxxxxxx Xxxxx X/X X/X X/X
Sample 1
SLASH TREATMENT Subdivision or Unit No. Specified Method Maximum Height of Decks Landings ALL MACH - Machine Piling: slash DECK – Decking Large Material: tops and non- sawtimber trees 12 feet Disposal Sites N/A N/A N/A Slash Treatment Methods Continued
Sample 1

Related to SLASH TREATMENT Subdivision or Unit No

  • Claim for Preferential Tariff Treatment 1. The importing Party shall require a certificate of origin for an originating good of the exporting Party from importers who claim the preferential tariff treatment for the good.

  • Denial of Preferential Tariff Treatment The Customs Authority of the importing Party may deny a claim for preferential tariff treatment when:

  • Commingling of Resold Services with Unbundled Network Elements and Combinations of Unbundled Network Elements 6.7.1 To the extent it is Technically Feasible and pursuant to the terms of Section 9.1, CLEC may Commingle Telecommunications Services purchased on a resale basis with an Unbundled Network Element or combination of Unbundled Network Elements.

  • Conflicts with RS Means Unit Price Book If the terms of the solicitation referenced RS Means Unit Price Book occur, the RS Means Book shall control if it determines the legality of the solicitation award as it relates to the requisite Means Unit Price Book.

  • Unbundled Voice Loop – SL2 (UVL-SL2 Loops may be 2-wire or 4-wire circuits, shall have remote access test points, and will be designed with a DLR provided to NewPhone. SL2 circuits can be provisioned with loop start, ground start or reverse battery signaling. OC is provided as a standard feature on XX0 Xxxxx. The OC feature will allow NewPhone to coordinate the installation of the Loop with the disconnect of an existing customer’s service and/or number portability service. In these cases, BellSouth will perform the order conversion with standard order coordination at its discretion during normal work hours.

  • Interconnection Facilities Engineering Procurement and Construction Interconnection Facilities, Network Upgrades, and Distribution Upgrades shall be studied, designed, and constructed pursuant to Good Utility Practice. Such studies, design and construction shall be based on the assumed accuracy and completeness of all technical information received by the Participating TO and the CAISO from the Interconnection Customer associated with interconnecting the Large Generating Facility.

  • CLEC to CLEC Conversions for Unbundled Loops 2.1.11.1 The CLEC to CLEC conversion process for Loops may be used by ITC^DeltaCom when converting an existing Loop from another CLEC for the same End User. The Loop type being converted must be included in ITC^DeltaCom’s Agreement before requesting a conversion.

  • Sub-loop Elements 2.8.1 Where facilities permit, BellSouth shall offer access to its Unbundled Sub-Loop (USL) elements as specified herein.

  • Xxx Treatment We have not promised you any particular tax outcome from buying or holding the Note.

  • CONFIDENTIAL TREATMENT REQUESTED Confidential portions of this document have been redacted and have been separately filed with the Commission.

Time is Money Join Law Insider Premium to draft better contracts faster.