Work Required. The City requires that the successful bidder perform a complete and satisfactory job in accordance with the Contract Documents.
Work Required. Required to pack, ship and receive all materials, pertaining to the Company. May be responsible for the receipt, pick-up and/or delivery and custody of all materials in his charge. Arrange for shipping of customers' parts and materials. To follow up on late or missing shipments, pickup and delivery of packages. Any other duties required by Supervisor.
Work Required. Employee may, at the City’s option, be required to work for the Xxxxxxx Police Department while attending the Training, and may be required to patrol, dispatch, operate computer systems, perform clerical tasks, or do other duties as assigned by the Chief of Police or the Chief’s designee. The hours expended by Employee in attending the Training and service to the Xxxxxxx Police Department will be subject to the same limitations and compensatory time policies as apply to all police officers of the City.
Work Required. Buyer acknowledges that the locomotive requires modification of the couplers to conform to Union Pacific requirements for alignment control before placement for interchange. If it so chooses Buyer agrees to provide all required parts and labor to convert this locomotive to acceptable condition for interchange. If locomotive is modified for interchange, Seller agrees to place the Locomotive at the interchange of the Union Pacific Railroad in Portola, CA, at no charge to Buyer following acceptance of the Locomotive for interchange. Exact timing of interchange will be coordinated by the Seller and Buyer separate from this agreement.
Work Required. The term “Work” includes all labor, materials, services, equipment, tools, transportation, power, water, permanent and temporary utilities, connections, provisions for safety, and all incidental and other things necessary to produce the finished construction of the Project as described by the Contract Documents. XXXX agrees to provide all labor, materials, equipment, tools and services necessary, and to do everything required by the Contract Documents as necessary to complete all Work required for the Project within the time specified for Substantial Completion and Final Completion of the Work.
Work Required. The Specifications and Drawings are intended to be complementary, and what is called for by either shall be as binding upon Contractor as if called for by both. The Work shall be complete in every detail. However, should any of the Work or any material be required which Work or material is not set forth in the Specifications or on the Drawings, either directly or indirectly, but which is nevertheless necessary for the proper carrying out of the intent thereof, including variations as may be necessary to conform to the conditions of the actual Work, Contractor agrees the same to be implied and required and shall perform all Work and furnish all such material as fully as if said Work and/or material were particularly delineated or described without additional costs to Owner. Contractor shall not be relieved of any obligations or responsibilities with respect to the Work except by written consent of Owner.
Work Required. Buyer acknowledges that the Lounge Car may require repairs to conform to interchange requirements. If it so chooses Buyer agrees to provide all required parts and labor to repair this Lounge Car to acceptable condition for interchange. Seller agrees to place the Lounge Car at the interchange of the Union Pacific Railroad in Portola, CA, at no charge to Buyer following acceptance of the Lounge Car for interchange. Exact timing of interchange will be coordinated by the Seller and Buyer separate from this agreement.
Work Required. Area A - 1.3ha – Intact peat with 0.75x0.75m semi impeded drains. This surface is very wet Bunded cells Appendix 5 of 30x30m need to be constructed across the site with attention where the bunds cross the drains. All degraded peat/vegetation needs to be removed before good ‘clay like’ peat is used to fill the drain. • Bund/cell construction – Bunds will be 150mm high x 0.75 - 1m wide bund. Construction as follows: o Remove about 0.75m to 1m width of vegetation (Put to side to be re used in covering the bund). o Dig out the thin layer of degraded peat possibly up to 0.5 m deep until you reach ‘clay like’ peat. o Check this surface for cracks etc (If cracks are found then dig out to the bottom of the crack, then return the peat and squash in to seal the crack) o Create a borrow pit on the uphill side of the bund and acquire good ‘clay like ‘ peat which is then used to top off the peat in the trench to a height of 150mm above ground level. Squash and form the peat into an appropriate shape and top with vegetation. o Any degraded peat/tree roots to be put in borrow pit and the borrow pit flattened off as much as possible. o Borrow pits must be separate and not joined up to form a new ditch. o Bund to be covered with previously removed turf stretched to cover the bund surface. o This bund will link to cells via bunds at 90 degrees that will be constructed on the upper surface Area B - 3.7ha - Intact peat containing drains around 0.75x0.75m, standing dead trees and previously cut but still growing rhododendron clumps. This surface is very wet and soft. Bunded cells of 30x30m need to be constructed. Any trees in the line of the bund need to be felled and the remains cut into small lengths and deposited in the cell. Any root plates along the line of the bund need to be lifted out and placed into a borrow pit. Bund construction as for Area A Area C - 13.0ha - Intact peat containing drains varying from 0.50x0.50m to 1x1m, mulched tree and rhododendron residues as well as rootstocks which will be above the surface in places. This surface is very wet and soft. 10ha bunded cells of 20x20 and 3ha at 20x10m need to be constructed. Any root plates along the line of the bund need to be lifted out and placed into a borrow pit. Bund construction as for area A
Work Required a. Research Title: "Development of Technologies that Control Scar Contracture after Burn Injuries "
Work Required. The project will construct bridge and structure replacements for low water crossings at all four locations. The improvements will include any walls, roadway alignments/ realignments, drainage, signing and safety improvements, excavation and permits necessary to build the structures and provide an appropriate roadway surface based on the existing approach roadway type. Construction of the project will be completed by a contractor selected by CFLHD. Onsite oversight will be conducted by CFLHD and project design is nearing completion. Construction oversight will be in accordance with CFLHD project plans, specifications and policies.
