Quantity Computations Sample Clauses

Quantity Computations. The quantity of dredged material removed and to be paid for will be measured by the cubic yard by computing the volume along the centerline between the "before-dredging" cross sections and the required dimensions as shown on the contract drawings using the average end area method. NO ALLOWANCE WILL BE MADE FOR EXCESSIVE DREDGING EXCEPT AS PROVIDED IN PARAGRAPH "EXCESSIVE DREDGING."
AutoNDA by SimpleDocs

Related to Quantity Computations

  • Time Computation Saturday, Sunday and holidays recognized by this Agreement shall not be counted under the time procedures established in this Agreement.

  • Balance Computation Method For all dividend-bearing Accounts, dividends are calculated by the average daily balance method which applies a daily periodic rate to the average daily balance for the average daily balance calculation period. The average daily balance is determined by adding the full amount of the principal in Your Account for each day of the period and dividing that figure by the number of days in the period. Accrual on Noncash Deposits. For dividend-bearing Accounts, dividends will begin to accrue on the business day that You deposit noncash items (e.g. checks) into Your Account.

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Measuring EPP parameters Every 5 minutes, EPP probes will select one “IP address” of the EPP servers of the TLD being monitored and make an “EPP test”; every time they should alternate between the 3 different types of commands and between the commands inside each category. If an “EPP test” result is undefined/unanswered, the EPP service will be considered as unavailable from that probe until it is time to make a new test.

  • Measuring DNS parameters Every minute, every DNS probe will make an UDP or TCP “DNS test” to each of the public-­‐DNS registered “IP addresses” of the name servers of the domain name being monitored. If a “DNS test” result is undefined/unanswered, the tested IP will be considered unavailable from that probe until it is time to make a new test.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Computations Unless otherwise expressly set forth herein, any accrued interest on any Loan, any Fees or any other Obligations due hereunder shall be computed on the basis of a year of 360 days and the actual number of days elapsed.

  • Interest Eligibility and Computation If NYSERDA fails to make Prompt Payment, NYSERDA shall pay interest to the Contractor on the Payment when such interest computed as provided herein is equal to or more than ten dollars ($10.00). Interest shall be computed and accrue at the daily rate in effect on the Date of Payment, as set by the New York State Tax Commission for corporate taxes pursuant to Section 1096(e)(1) of the Tax Law. Interest on such a Payment shall be computed for the period beginning on the day after the Payment Due Date and ending on the Date of Payment.

  • Revenue Metering The Connecting Transmission Owner’s revenue metering will be located on the generator side of the 115kV breaker at the Xxxxx Solar Collector Substation and will consist of: • three (3) combination current/voltage transformer (“CT/VT”) units (manufacturer and model ABB/Xxxxxxx KXM-550, GE Grid Solutions KOTEF 000.XX, or other equivalent specified by Connecting Transmission Owner); and • one (1) revenue meter. The ratios of the CTs and VTs will be provided by Connecting Transmission Owner upon its review of the Interconnection Customer’s design documents. (Note: Connecting Transmission Owner’s revenue metering CTs and VTs cannot be used to feed the Interconnection Customer’s check meter.) SERVICE AGREEMENT NO. 2556

  • Computation of Overtime In computing overtime a period of thirty (30) minutes or less shall be counted as one-half (½) hour and a period of more than thirty (30) minutes but less than sixty (60) minutes shall be counted as one (1) hour.

Time is Money Join Law Insider Premium to draft better contracts faster.