Contract Drawings. The Contract Drawings provided for tendering purpose with the tender documents shall be used as a reference only. Contractor should visualize the nature and type of work contemplated and to ensure that the rates and prices quoted by him in the xxxx of quantities take due consideration of the complexities of work involved during actual execution / construction as experienced contractors in the field. The tendered rates / prices for the work shall be deemed to include the cost of preparation, supply and delivery of all necessary drawings, prints, tracings and negatives which the contractor is required to provide in accordance with the contract.
Contract Drawings. A In general, the Drawings shall indicate dimensions, position and type of construction. The Specifications shall indicate the qualities and the methods. The Bill of Quantities shall indicate the quantum and the rate for each item of work. Any work indicated on the Drawings and not mentioned in the specifications or vice versa shall be deemed as though fully set forth in both. Work not specifically detailed, called for, marked or specified shall be the same as similar parts that are detailed, marked or specified.
Contract Drawings. Drawings and other data designated as Contract Drawings prepared by Engineer for this Contract which show the character and scope of the Work to be performed and are referred to in the Contract Documents.
Contract Drawings. All drawings shall be drawn and provided in the AutoCAD format version operating in Microsoft Windows operating system currently being used by the Owner. No translations from other format versions will be allowed. Electronic documents shall be provided to the Owner upon request. At a minimum, PDF versions of all submittal documents and PDF and AutoCAD versions of bid documents and record drawings shall be provided.
Contract Drawings. 843-B205-01 OUTBOARD PROFILE 843-B215-01 GENERAL ARRANGEMENT
Contract Drawings. Any work shown in the Contract Drawings or in drawings or materials supplied by Contractor but not mentioned in the Contract Specifications and any work mentioned in the Contract Specifications but not shown in the Contract Drawings shall be performed as if both mentioned in the Contract Specifications and set forth in the Contract Drawings. Should any conflict or discrepancy appear or any disagreement arise in the interpretation of either the Contract Drawings or the Contract Specifications, such will be subject to the provisions of Section 40.3 hereof.
Contract Drawings. Engineer shall issue from time to time free of charge two sets of Contract Drawings, Approved for Construction, to the Contractor and one copy thereof to the Employer. Additional copies as and when required shall be supplied by the Engineer and costs shall be reimbursed by the Contractor. In case the issue of drawings does not conform to the programme as planned and approved, the contractor shall immediately submit a revised programme so that; by deployment of adequate resources, the Work is completed within the stipulated time period. The Project Management Consultant may from time to time during the course of contract issue the Contractor with revised contract drawings and the Contractor shall ensure that all superseded drawings are removed from site and stored in a lockable cabinet as directed by the Engineer and replaced by revised contract drawings. The Contractor shall ensure that a complete up to date Register of Drawing is maintained at Site. All Contract Drawings shall be properly filed and indexed for ready reference. The Contractor shall ensure that only the valid up to date contract drawings are used for preparation of working drawings, setting out, construction etc.
Contract Drawings. Revised Construction Documents prepared by ArcDesign Engineering, dated 12/29/20, titled: “West Elementary School Drawing Issue 12292020 – Stamped” Consisting of the following sheets:
A-1 Title Sheet A-2 Module Layout A-3.1 Roof Section 1 A 3.2 Roof Section 2 & Roof Section 3 E-1 Single Line Diagram E-2 Labeling E-3 Electrical component cutsheets
Contract Drawings. The developer’s contractor shall legibly mark to record the actual construction on the project record set of prints of the Contract Drawings, the following:
1. Any and all changes or revisions to the original drawings for both water and sewer.
2. Plan view and profile of the sewers and any revisions.
3. Location of all tees or wyes as measured from the nearest downstream manhole.
4. Location of all valves and blowoffs shall be located by measurement from two separate, easily identifiable, stationary points. These points shall be manholes, power poles, electric vaults, telephone pedestals, buildings, or any other permanent type items which are not subject to change in size, shape, or location. Property pins may be used if no other reference point is available.
5. Length of the sewer service line measured from the center of the collector line to the end of the pipe.
6. Approximate depth of the end of each sewer service pipe.
7. Where the sewer service line is not perpendicular to the centerline of the collector line, a measurement from the downstream manhole must be made to a point located on the collector line that is perpendicular to the end of the sewer service line. The length of the sewer service from this point to end of the pipe must also be noted.
8. All bench marks used for sewer line design and construction must be shown on both construction and record drawings. Permanent bench marks shall be located adjacent to every third manhole on the project and the description and elevation noted on the construction plans.
9. Changes made by change order or field order.
10. After completion of the work, the developer shall have prepared a set of project record drawings by drafting all noted changes and revisions as described in