Measurement conditions Sample Clauses

Measurement conditions. 3.1. If a visual inspection of the dipped‑beam pattern on the screen or a photometric method is used, measurement shall be carried out in a dark environment (for example, a dark room) of sufficient area to allow the vehicle and the screen to be placed as shown in Figure 1. Headlamp centres of reference shall be at a distance from the screen of at least 10 m.
AutoNDA by SimpleDocs
Measurement conditions. Ingestion of alcoholic beverages is not allowed 16 h prior to measurement. This applies to all objective measurements. When in doubt, a blood sample must be taken to verify that the alco- hol level is below 0.1 mg/g (alternative 0.1 ‰)(10). All objective measurements must be made under standardized indoor mea- surement conditions. The indoor temperature must be between 18 and 35 degrees Celsius and the humidity must be at least 30%. The period of adaptation depends on the ratio between outdoor and indoor temperature. A minimum time period of 10 min is recommended for acclimatization to indoor room tempe- rature and humidity in the waiting room. The patient should be
Measurement conditions. 2.1. The fuel to be used shall be one or the other of the fuels mentioned in paragraph 3.2. of annex 4 of this Regulation.

Related to Measurement conditions

  • PAYMENT CONDITIONS The price of the whole accommodation service booked is always payable by the Guest in advance, at the latest upon arrival in the hotel. Set-off by the Guest is excluded unless the set- off relates to an undisputed or legally confirmed claim. Valid means of payment are cash in Euros, EC card, Master Card, Visa Card, Diners Card and American Express. For payment settlement we use the 3D Secure 2.0 system for secure and additional customer authorisation. For further information on data processing for payment transactions see xxxxx://xxx.xxxxx-xxx.xxx/en/data-privacy/.

  • Test conditions 6.1.1. The test shall be performed on a flat, dry concrete or asphalt surface affording good adhesion.

  • PROJECT CONDITIONS A. The Grantee agrees to the following Project Conditions:

  • Contract Conditions This section contains conditions which shall be complied with during the performance of this contract. The conditions come in two parts, general conditions and special contract requirements.

  • INCLEMENT CONDITIONS Section 1.

  • PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan‌ (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction

  • Performance Requirements 1. Neither Party may impose or enforce any of the following requirements, or enforce any commitment or undertaking, in connection with the establishment, acquisition, expansion, management, conduct or operation of an investment of an investor of a Party or of a non-Party in its territory:

  • Performance Measurement Satisfactory performance of this Contract will be measured by:

  • Safe Conditions Whenever an employee reports a condition which the employee feels represents a violation of safety or health rules and regulations or which is an unreasonable hazard to persons or property, such conditions shall be promptly investigated. The appropriate administrator shall reply to the concern, in writing, if the employee's concern is communicated in writing.

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

Time is Money Join Law Insider Premium to draft better contracts faster.