APPROVAL & TESTING OF WELDING PROCEDURES Sample Clauses

APPROVAL & TESTING OF WELDING PROCEDURES. The Contractor shall carry out procedure tests in accordance with IS:7307 to demonstrate by means of a specimen weld of adequate length on steel representative of that to be used. The test weld shall include weld details from the actual construction and it shall be welded in a manner simulating the most unfavorable instances of fit-up, electrode condition etc., which are anticipated to occur on the particular fabrication. Where material analyses are available, the welding procedure shall be carried out on material with the highest carbon equivalent value. After welding, but before the relevant tests given in IS:7307 are carried out, the test weld shall be held as long as possible at room temperature, but in any case not less than 72 hours, and shall then be examined for cracking. The examination procedure shall be sufficiently rigorous to be capable of revealing significant defects in both parent metal and weld metal. After establishing the welding method, the Contractor shall finally submit the welding procedure specification in standard format given in IS:9595 before starting the fabrication.
AutoNDA by SimpleDocs

Related to APPROVAL & TESTING OF WELDING PROCEDURES

  • Drug Testing Procedures a. The testing procedures and safeguards provided in this policy shall be adhered to by any laboratory personnel administering departmental drug tests.

  • Testing Procedures Testing will be conducted by an outside certified Agency in such a way to ensure maximum accuracy and reliability by using the techniques, chain of custody procedures, equipment and laboratory facilities which have been approved by the U.S. Department of Health and Human Services. All employees notified of a positive controlled substance or alcohol test result may request an independent test of their split sample at the employee’s expense. If the test result is negative the Employer will reimburse the employee for the cost of the split sample test.

  • Testing Procedure A. For alcohol testing, the member shall be first given a breath test, at the collection site, followed by a confirmatory urine test only where the breath test reveals an initial positive alcohol level of .04 grams per 210 l. of breath. If the initial breath test results are below this level, testing shall be discontinued; if confirmatory urine tests results are below a level equivalent to .04 grams per 210 l. of breath, the confirmatory test shall be considered negative.

  • Hiring Procedures Nothing contained in this Article 4 shall impair any of the rights of the Employer to hire new or additional employees to meet the employment needs of the Employer, in accordance with the terms and provisions of this collective bargaining Agreement or to meet the obligations of the Employer under Article 2, Section H of this Agreement or to take affirmative steps to comply with any requirements under any applicable Federal or State law prohibiting discrimination in employment.

  • Working Procedure Assist in the definition and analysis of vehicle system requirements. Prepare technical specification sheets. Evaluate vendor proposals to ensure the specifications are met. Assist in the generation and checking of test reports. May conduct and witness factory acceptance tests, dynamic performance tests and may provide support for commissioning of vehicles at customers' premises. Perform other related duties as required.

  • HIRING PROCEDURE B5.1 The Employer agrees that whenever employees covered by this Agreement are required, the Employer shall call the Union office of the Local Union(s) having jurisdiction.

  • Hearing Procedures The hearing shall be conducted to preserve its privacy and to allow reasonable procedural due process. Rules of evidence need not be strictly followed, and the hearing shall be streamlined as follows:

  • BIDDING PROCEDURES 4.1. Bidders have to login at EHSAN AUCTIONEERS SDN. BHD. Website using the same registered email 30 minute before Auction Time.

  • ORDERING PROCEDURES 6.1 If the Authority or any Other Contracting Body decides to source the Services through this Services Framework then each Contracting Body shall be entitled at any time, during the Term to place an order for the Services from the Supplier by serving an Order in accordance with Framework Agreement Schedule 5 (Ordering Procedure).

  • Loop Testing/Trouble Reporting 2.1.6.1 Think 12 will be responsible for testing and isolating troubles on the Loops. Think 12 must test and isolate trouble to the BellSouth portion of a designed/non- designed unbundled Loop (e.g., UVL-SL2, UCL-D, UVL-SL1, UCL-ND, etc.) before reporting repair to the UNE Customer Wholesale Interconnection Network Services (CWINS) Center. Upon request from BellSouth at the time of the trouble report, Think 12 will be required to provide the results of the Think 12 test which indicate a problem on the BellSouth provided Loop.

Time is Money Join Law Insider Premium to draft better contracts faster.