ROLLING SHUTTERS Sample Clauses

POPULAR SAMPLE Copied 1 times
ROLLING SHUTTERS. Rolling shutters shall conform to IS: 6248. These shall include necessary locking arrangement and handles etc. These shall be suitable for fixing in the position as specified i.e. outside or inside on or below lintel or between jambs of the opening. The door shall be either push and pull type or operated with mechanical device supplied by the firm. Shutters up to 10 sq. meter shall be of push and pull type and shutters with an area of over 10 sq.meter shall generally be provided with reduction gear operated by mechanical device with chain or handle, if bearings are specified for each of operation, these shall be included in the rate.
View Source
ROLLING SHUTTERS. The rolling shutters shall conform to IS: 6248. Rolling shutters shall be supplied of specified type, with accessories. The size of the rolling shutters shall be as specified in the drawings. The shutters shall be constructed with interlocking lath sections formed from cold rolled steel snips not less than 0.9 mm. thick and 80 mm wide, for shutters up to 3.5 m. width and not less than 1.25 mm. thick and 80 mm. wide, for shutters 3.5m in width and above, unless otherwise specified. Guide channels shall be of mild steel deep channel section and roll pressed or built-up (fabricated), with joint less construction. The thickness of the sheet used shall not be less than 3.15 mm. Hood covers shall be made of ▇.▇. ▇▇▇▇▇▇, not less than 0.90 mm. thick. For shutters having width of 3.5 m. and above, the thickness of M.S. sheet for the hood cover shall be not less than 1.25
View Source
ROLLING SHUTTERS. Rolling shutters shall consist of 75 mm wide 18 gauge M.S. laths machine rolled and straightened with an effective bridge depth of 16 mm. The laths shall be interlocked through their entire length and jointed together at the end with end locks. These shall be mounted on specially designed pipe shaft. Each lath section shall be a continuous single strip piece without any joint. The spring shall be prepared from unbreakable high tensile spring steel wire or strip of adequate strength to balance the shutter in all positions. The spring assembly shall be supported on strong mild steel or malleable cast iron bracket shaped to fit the lintels. The shutter shall be complete with door suspension shafts, guides, locking arrangements, brackets, pulleys with ball bearings, pushing hooks, handles, top covers etc. Fixing shall be done accurately in a ▇▇▇▇▇▇▇ like manner such that the operation of the shutter is easy and smooth. Rate includes applying one coat of rust remover, one coat of yellow zinc chromate primer and three coats of approved make and shade of flat/enamel paint etc. Rolling shutters shall be measured in square meters of the clear opening to which they are fixed and in no case top drum with cover and channels shall be paid extra or shall be calculated in area.
View Source

Related to ROLLING SHUTTERS

  • Wash all machine-washable bedding, drapes, and clothing, on the hottest water temperature and dry on the highest heat setting. Items that cannot be washed must be taken to a dry cleaner who MUST be informed of the issue. You must safely discard ALL items that cannot be decontaminated.

  • Load Shedding The Distributor may carry out Load Shedding in the following circumstances: (a) Maintenance of Network equipment: if the Distributor wishes to inspect or effect alterations, maintenance, repairs, or additions to any part of the Network, subject to clauses 4.6, 4.8, 4.10, and Schedule 5 as applicable; (b) Permitted by Service Standards: as permitted by the Service Standards, if the Customer has elected to receive an interruptible or otherwise non-continuous supply of electricity; (c) Compliance with instructions from the System Operator: (i) to comply with a request or instruction received from the System Operator in accordance with the Code; or (ii) if communication with the System Operator has been lost, and the Distributor reasonably believes that, had communication with the System Operator been maintained, the Distributor would have received a request or instruction from the System Operator to shed load in accordance with the Code; (d) Maintain security and safety: to maintain the security and safety of the Network in order to: (i) maintain a safe environment, consistent with the Distributor's health and safety policies; (ii) prevent unexpected short term overloading of the Network; (iii) prevent voltage levels rising or falling outside of legal requirements; (iv) manage System Security; and (v) avoid or mitigate damage to the Network or any equipment connected to the Network; (e) Compliance with the Code: to comply with the Code or the law; or (f) Other circumstances: for any other purpose that, in the Distributor’s reasonable opinion, and in accordance with Good Electricity Industry Practice, requires the interruption or reduction of delivery of electricity to any ICP.

  • Heating, Ventilating and Air Conditioning General Office Area: The building shall be equipped with a combination heating, ventilation and air conditioning system. The system shall have ducted supply and return air. The space above the ceiling shall not be used as a supply or return plenum. The systems shall be sized in accordance with the

  • Rolling Stock The Recipient agrees that any procurement for rolling stock will comply with 49 U.S.C. § 5325 (Contract Requirements), 49 U.S.C. § 5323(j) (Buy America Requirements), 49 U.S.C. § 5323(m) (Pre-Award and Post Delivery Requirements), and 49 U.S.C. § 5318(e) (Bus Testing Requirements), and their implementing regulations.

  • WINDOW CLEANING Tenant shall not clean, nor require, permit, suffer or allow any window in the Premises to be cleaned from the outside in violation of Section 202 of the Labor Law, or any other Requirement, or of the rules of the Board of Standards and Appeals, or of any other board or body having or asserting jurisdiction.