Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
METERING AND BILLING Metering requirements and billing procedures shall be set forth in the AEC rate schedule(s) applicable to the electric service account assigned to the location where the Generating Facility is connected.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Marketing and Outreach CONTRACTOR shall identify culturally and linguistically appropriate measures for reaching older adults in need of transportation and determine procedures for implementation of outreach, which may include, but is not limited to, brochures, flyers, and public presentations. In order to ensure effective collaboration and coordination of services, a CONTRACTOR shall be required to submit drafts of all printed materials related to outreach and marketing of OoA Senior Non-Emergency Medical Transportation Fixed-Price Per Mile Program services to OoA for approval before publication and dissemination.
PACKING AND MARKING Seller shall package all Goods shipped under this Order in accordance with the requirements in this Order, or, if requirements are not specified, in accordance with standard commercial practices customary for similar shipments. When shipping any Goods that are food or food packaging, Seller will ship the Goods under sanitary conditions using carriers suitable for the transport of such Goods that will not render the Goods contaminated with filth, injurious to health, or otherwise adulterated (e.g., carriers that have not been used to transport garbage, waste or other refuse). In each master carton or container in which Goods are shipped, Seller shall include a certificate of analysis, bill of lading, and packing list indicating this Order number, description, quantity, HSY item numbers, and other identifying information corresponding to the information in this Order. Seller shall clearly mark all packages in accordance with all applicable laws and shall label each unit of the Goods with the country of origin, weight, and name of manufacturer. Seller shall ensure that a receiving document/proof-of-delivery is issued to HSY for any shipment made to a third party location. All costs, fines or penalties incurred or assessed due to improper packing or marking will be Seller’s responsibility, and if paid by HSY, will be deducted from amounts owed to Seller. Seller will notify HSY of the number of packages, size, weight, method of protection during shipment and method of storage and protection upon arrival at destination.
Local Control Center, Metering and Telemetry The NTO shall operate, pursuant to ISO Tariffs, ISO Procedures, Reliability Rules and all other applicable reliability rules, standards and criteria on a twenty-four (24) hour basis, a suitable local control center(s) with all equipment and facilities reasonably required for the ISO to exercise ISO Operational Control over NTO Transmission Facilities Under ISO Operational Control, and for the NTO to fulfill its responsibilities under this Agreement. Operation of the NYS Power System is a cooperative effort coordinated by the ISO control center in conjunction with local control centers and will require the exchange of all reasonably necessary information. The NTO shall provide the ISO with Supervisory Control and Data Acquisition (“SCADA”) information on facilities listed in Appendices A-1 and A-2 herein as well as on generation and merchant transmission resources interconnected to the NTO’s transmission facilities pursuant to the ISO OATT. The NTO shall provide metering data for its transmission facilities to the ISO, unless other parties are authorized by the appropriate regulatory authority to provide metering data. The NTO shall collect and submit to the ISO billing quality metering data and any other information for its transmission facilities required by the ISO for billing purposes. The NTO shall provide to the ISO the telemetry and other operating data from generation and merchant transmission resources interconnected to its transmission facilities that the ISO requires for the operation of the NYS Power System. The NTO will establish and maintain a strict code of conduct to prevent such information from reaching any unauthorized person or entity.
Program Monitoring and Evaluation (c) The Recipient shall prepare, or cause to be prepared, and furnish to the Association not later than six months after the Closing Date, a report of such scope and in such detail as the Association shall reasonably request, on the execution of the Program, the performance by the Recipient and the Association of their respective obligations under the Legal Agreements and the accomplishment of the purposes of the Financing.”
Monitoring and Evaluation a. The AGENCY shall expeditiously provide to the COUNTY upon request, all data needed for the purpose of monitoring, evaluating and/or auditing the program(s). This data shall include, but not be limited to, clients served, services provided, outcomes achieved, information on materials and services delivered, and any other data required, in the sole discretion of the COUNTY, that may be required to adequately monitor and evaluate the services provided under this Contract. Monitoring shall be performed in accordance with COUNTY’S established Noncompliance Standards, a copy of which is attached hereto and incorporated by reference as Attachment “C”.
Xxxxxxxx, 121 Cal App.4th Supp. 7 (2004), CIV Code 1962 Colorado $50.00 or 5% of past due rent C.R.S. § 00-00-000 Connecticut Not defined No statute Delaware 5% of the monthly rent amount Title 25, § 5501(d) Florida Not defined No statute Georgia “All contracts for rent shall bear interest from the time the rent is due” Hawaii 8% of the monthly rent amount § 521-21(f) Idaho Not defined No statute Illinois Outside Chicago – Not defined Chicago only – $10.00 per month for the first $500.00 in monthly rent plus five percent per month for any amount in excess of $500.00 in monthly rent for the late payment of rent. No statute 5-12-140(h) Indiana Not defined No statute Iowa If the rent does not exceed $700/month, the late fee cannot exceed more than $12/day per day or $60/month. If the rent is greater than $700/month, the late cannot exceed more than $20/day or $100/month.
Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction.
