Felling and Bucking Sample Clauses
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.▇▇▇ ▇▇▇▇▇ ▇▇▇▇▇▇▇. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The ▇▇▇▇▇ heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where ▇▇▇▇▇ heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A.2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Stand- ards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchanta- bility factor, whichever is stated in A2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges.
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Stand- ards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchanta- bility factor, whichever is stated in A2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not ex- tend outside Clearcutting Units, construction clearings, and areas of regeneration cutting. B6.▇▇▇ ▇▇▇▇▇ ▇▇▇▇▇▇▇. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Con- tractor determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Contractor shall re-cut high stumps so they will not ex- ceed heights specified in A6 and shall dispose of sev- ered portions in the same manner as other logging de- bris. The ▇▇▇▇▇ heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Contract Area Map shows special areas where ▇▇▇▇▇ heights are lower for aesthetic, land treat- ment, or silvicultural reasons. B6.413 Bucking Lengths. Trees shall be bucked in various lengths to obtain the greatest utiliza- tion of material meeting Utilization Standards.
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in AT2. Con- tractor may buck out cull material when necessary to pro- duce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net Measure in percentage of gross Measure, or based on the merchantability factor, whichever is stated in AT2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges. BT6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to re- sidual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth on Page 1. Purchaser may buck out cull material when necessary to produce pieces meet- ing Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated on Page 1. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not extend outside Clearcutting Units, clearings, and areas of regeneration cutting.
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Felling shall be done by saws or shears. Trees may not be left hanging on other trees. All hung trees or spring poles must be fell or released, dropped or pulled down to the ground the day they occur. ▇▇▇▇▇ Heights: Stumps shall not exceed, on the side adjacent to highest ground, the maximum height of 12 inches, unless agreed otherwise in writing by Seller or their Representative. Limbing: When necessary to minimize damage to residual stand during skidding, exposed limbs shall be cut from products prior to skidding. Such limbs may be left uncut which cannot be cut with reasonable safety. Skidding: In so far as ground conditions permit products shall not be skidded against unmarked trees or groups of pole trees or groups of reproduction, and skidders or tractors shall be equipped with winch to facilitate skidding. Landings and Skid Trails: Location of all landings, skid roads, skid trails shall be agreed upon prior to construction or use in writing. Landings and major skid trails will be flagged in prior to construction and use.
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting.