Compliance with Standards Although the standards for workmanship, material, and equipment have been selected in these specifications as a basis of reference, standards and specifications of the other bank member countries and recommendations of standards international organizations will be acceptable provided they are substantially equivalent to the designated standards and provided furthermore that the contractor submits for approval detailed specifications which he proposes to use. Reference to brand names or catalog numbers if any in these specifications have been made only for that equipment for which it has been determined that a degree of standardization is necessary to maintain certain essential features. And in certain cases such references have also been made for purposes of convenience to specify the requirements, in either case offers of alternative goods, which have similar characteristics and provide performance and quality at lease equal to those specified are acceptable. If the contractor offers materials, equipment, design calculations or tests, which conform to standards other than those specified, full details of the differences between the proposed standards and that specified in so far as they affect the design or purpose of the equipment, are to be supplied by the contractor if called upon to do so by the engineer, where required by the engineer for approval purposes, the contractor shall supply, without charge, duplicate copies of the proposed standards with English translations of the relevant portions. The contractor shall have available in his place of business (or in his supplier’s works) the relevant copies of standards or codes used for the use of the Engineer.
Compliance with Federal Regulations (1) Any contract entered pursuant to this solicitation shall contain the following provisions: All USDOT-required contractual provisions, as set forth in FTA Circular 4220.1F, are incorporated by reference. Anything to the contrary herein notwithstanding, FTA mandated terms shall control in the event of a conflict with other provisions contained in this Agreement. Contractor shall not perform any act, fail to perform any act, or refuse to comply with any grantee request that would cause the recipient to be in violation of FTA terms and conditions. Contractor shall comply with all applicable FTA regulations, policies, procedures and directives, including, without limitation, those listed directly or incorporated by reference in the Master Agreement between the recipient and FTA, as may be amended or promulgated from time to time during the term of this contract. Contractor’s failure to so comply shall constitute a material breach of this contract.
Compliance with Federal Requirements Federal money will be used or may potentially be used to pay for all or part of the goods, construction or services under the Contract. The Contractor is responsible for compliance with all federal requirements imposed on the funds and accepts full financial responsibility for any requirements imposed by the Contractor’s failure to comply with federal requirements. Certification regarding Debarment, Suspension, Ineligibility, and Voluntary Exclusion. Federal money will be used or may potentially be used to pay for all or part of the work under the Contract, therefore Contractor certifies that it is in compliance with federal requirements on debarment, suspension, ineligibility and voluntary exclusion specified in the solicitation document implementing Executive Order 12549. Contractor’s certification is a material representation upon which the Contract award was based. Contingency Fees Prohibited.
Compliance with Federal Law Contractor shall comply with all applicable federal laws, including, without limitation, those set forth in Exhibit D, which is attached and incorporated into this Contract by this reference.
COMPLIANCE WITH FEDERAL LAWS AND REGULATIONS Contractor, to the extent applicable to this Agreement, shall comply with the following Federal laws and regulations as set forth in 24 CFR §§570.600-612:
Compliance with Statutes The Borrower and its Subsidiaries are in compliance in all material respects with all applicable statutes, regulations and orders of, and all applicable restrictions imposed by, all governmental bodies and have all necessary permits, licenses and other necessary authorizations with respect to the conduct of their businesses and the ownership and operation of their properties except where the failure to so comply or hold such permits, licenses or other authorizations could not reasonably be expected to have a Material Adverse Effect.
COMPLIANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS If required within the Authorized User Agreement, Contractor will provide verification of compliance with specific Federal, State and local regulations, laws and IT standards that the Authorized User is required to comply with. See Appendix F – Primary Security and Privacy Mandates. AUTHENTICATION TOKENS The Authorized User Agreement may require authentication tokens for all systems. For more details, please see NYS ITS Policy S14-006 Authentication Tokens Standard or successor. MODIFICATION TO CLOUD SERVICE DELIVERY TYPE AND DESCRIPTION WITHIN AN AUTHORIZED USER AGREEMENT As Cloud services can be flexible and dynamic, delivery mechanisms may be subject to change. This may result in changes to the service type, description, or SKU. The State and Authorized Users require notification of any such changes to ensure security and business needs are met. Any changes to the description, type of service(s), or SKU (e.g., PaaS to IaaS) must be provided to OGS via Appendix C - Contract Modification Procedure. In addition, notification must be provided to the Authorized User for review and acceptance, prior to implementation. Any changes to the Authorized User Agreement will require the Authorized User to re-assess the risk mitigation methodologies and strategies and revise the Authorized User Agreement as needed.
COMPLIANCE WITH OTHER LAWS Secured Party may comply with any applicable state or federal law requirements in connection with a disposition of the Collateral and compliance will not be considered adversely to affect the commercial reasonableness of any sale of the Collateral.
Compliance with Accessibility Standards All parties to this Agreement shall ensure that the plans for and the construction of all projects subject to this Agreement are in compliance with standards issued or approved by the Texas Department of Licensing and Regulation (TDLR) as meeting or consistent with minimum accessibility requirements of the Americans with Disabilities Act (P.L. 101-336) (ADA).
COMPLIANCE WITH APPLICABLE LAWS AND STANDARDS 9.1.1 Each party must comply with all Applicable Laws in performing their obligations under this Agreement.
