Partial contour marking definition

Partial contour marking means a contour marking that indicates the horizontal dimension of the vehicle by a continuous line, and the vertical dimension by marking the upper corners.

Related to Partial contour marking

  • Partial confinement means confinement for no more than one

  • mine site means the mining lease the accommodation area and other areas provided for the facilities of the Company in the vicinity of the mining lease;

  • Premises Building Partial Damage shall herein mean damage or destruction to the building of which the Premises are a part to the extent that the cost of repair is less than 50% of the then replacement cost of such building as a whole.

  • Landing area means that part of a movement area intended for the landing or take-off of aircraft;

  • Building Area means the greatest horizontal area of a building within the outside surface of the exterior walls.

  • Acre-foot means the amount of water necessary to cover one acre of land one foot deep, or about 325,851 U. S. gallons of water.

  • bicycle parking space – occupant means an area that is equipped with a bicycle rack or locker for the purpose of parking and securing bicycles, and:

  • Building Square Footage or "BSF" means the square footage of assessable internal living space of a Unit, exclusive of any carports, walkways, garages, overhangs, patios, enclosed patios, detached accessory structure, other structures not used as living space, or any other square footage excluded under Government Code Section 65995 as determined by reference to the Building Permit for such Unit.

  • Premises Building Total Destruction means if the Building of which the Premises are a part is damaged or destroyed to the extent that the cost to repair is fifty percent (50%) or more of the then Replacement Cost of the Building.

  • Built-Up Area and/or “Covered Area” in relation to a Flat shall mean the floor area of that Flat including the area of balconies and terraces, if any attached thereto, and also the thickness of the walls (external or internal) and the columns and pillars therein Provided That if any wall, column or pillar be common between two Flats, then one-half of the area under such wall column or pillar shall be included in the built-up area of each such Flat.

  • Square Footage means the total gross horizontal areas of all floors, including usable basement and cellars, below the roof and within the outer surface of the main walls of buildings (or the center lines of party walls separating such buildings or portions thereof) or within lines drawn parallel to and two feet within the roof line of any building or portion thereof without walls (which includes, notwithstanding paragraph 3 below, the square footage of all porches), and including pedestrian access walkways or corridors, but excluding the following:

  • construction site means a workplace where construction work is being performed;

  • Facade means the entire building wall including a parapet;

  • Building site means a plot of land held for building purposes, whether any building is actually erected thereupon or not, and includes the open ground or courtyard enclosed by, or adjacent to, any building erected thereupon;

  • Drainage area means a geographic area within which stormwater, sediments, or dissolved materials drain to a particular receiving waterbody or to a particular point along a receiving waterbody.

  • Survey Area means the area of land or waters the subject of a Survey, or proposed to be the subject of a Survey.

  • Impact surface means an interior or exterior surface that is subject to damage by repeated sudden force such as certain parts of door frames.

  • Tight-fitting facepiece means a respiratory inlet covering that forms a complete seal with the face.

  • Approximate original contour means that surface configuration achieved by backfilling and grading of the mined area so that the reclaimed area, including any terracing or access roads, closely resembles the general surface configuration of the land prior to mining and blends into and complements the drainage pattern of the surrounding terrain, with all highwalls and spoil piles eliminated. Water impoundments may be permitted where the board determines that they are in compliance with section 34-33-120 (2)(h).

  • ILUA Area means the geographical area in relation to which the Framework ILUA applies, as specified in Schedule 2 of the Framework ILUA;

  • Building, structure, facility, or installation means all of the pollutant-emitting activities which belong to the same industrial grouping, are located on one or more contiguous or adjacent properties, and are under the control of the same person (or persons under common control) except the activities of any vessel. Pollutant-emitting activities shall be considered as part of the same industrial grouping if they belong to the same major group (i.e., which have the same two-digit code) as described in the Standard Industrial Classification Manual, 1972, as amended by the 1977 Supplement (U.S. Government Printing Office stock numbers 4101-0066 and 003-005-00176-0, respectively).

  • stacked bicycle parking space means a horizontal bicycle parking space that is positioned above or below another bicycle parking space and equipped with a mechanical device providing floor level access to both bicycle parking spaces.

  • Annexing area means an area that is annexed into a county, city, or town.

  • Basement means any area of the building having its floor subgrade (below ground level) on all sides.

  • Cultivation site means a location where cannabis is planted, grown, harvested, dried, cured, graded, or trimmed, or a location where any combination of those activities occurs.

  • Erection, construction, remodeling, repairing means all types of work done on a particular building or work at the site thereof in the construction or development of the project, including without limitation, erecting, construction, remodeling, repairing, altering, painting, and decorating, the transporting of materials and supplies to or from the building or work done by the employees of the Contractor, Subcontractor, or Agent thereof, and the manufacturing or furnishing of