Trading of Asset Linked Products. 6.1 An asset linked product:-
Trading of Asset Linked Products Sample Clauses
Related to Trading of Asset Linked Products
Preference for Domestically Manufactured Goods The provisions of paragraphs 2.54 and 2.55 of the Guidelines and Appendix 2 thereto shall apply to goods manufactured in the territory of the Borrower.
Payment for Forest Products Delivered Purchaser agrees to pay the State for delivered forest products at the following rate: $0.00/MBF $250.00/MBF for incorrect species delivery* $20/mbf for Utility logs (Adjusted Gross). Purchaser agrees to increase the above delivered payment rate as approved by the State in the event the location of delivery is changed per the G-026.2 clause. Purchaser will not be billed for any delivered logs that are scaled as containing metal. *When two or more log sorts from this project are delivered to the same destination, the species contained in them are not eligible for the species price reduction. P-036.2 Missorts and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet the sorting specifications in G-022.2 are considered mis-sorts. Purchaser receiving mis-sort Forest Products is required to pay the State at the bid price under this contract. However, when mis-sorted Forest Products amount to more than 5% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-sort threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-sort payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-sort price reduction are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-sorted will be calculated as follows: Payment Reduction = (B x M) x R Where: B = Bid rate from P-028.2 clause M = Mis-sorted volume exceeding threshold excluding utility R = Reduction factor* 0.2 for diameter mis-sort 0.3 for high quality mis-sort *Logs eligible for payment reduction based on multiple reduction factors will be calculated at the higher payment reduction factor. Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-sort payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-sorts shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code P-037.2 Mismanufacture and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet preferred log length specifications or multiples or combinations of preferred lengths and Forest Products delivered not meeting manufacturing standards as described in clause G-024.2 are considered mis- manufactured. Purchaser receiving mis-manufactured Forest Products is required to pay the State at the bid price under this contract. However, when mis-manufactured Forest Products amount to more than 8% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-manufacture threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-manufacture payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-manufacture price reductions are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-manufactured will be calculated as follows: Payment Reduction = (B x M) x (0.2) Where: B = Bid rate from P-028.2 clause M = Mis-manufactured volume exceeding threshold excluding utility Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-manufacture payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-manufacture shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Deliverables for an Authorized User Agreement (Transaction Deliverables must be identified, as a measure of progress in the Authorized User Agreement. A Deliverable as a bulk number of hours is not permissible under the OGS Centralized Contract. Retainage As part of the Mini-Bid, the Authorized User may elect to retain a percentage of each individual Deliverable payment of no more than 20% until the acceptance of the complete Deliverable or project. This retainage may be reduced as described in the Mini-Bid, when the Contractor substantially reduces the time required from the timeframes negotiated between the Authorized User and the Contractor for the completion and acceptance of a Deliverable.
OVERSEAS TRANSACTIONS 13.1 The Cardmember may use the Credit Card outside Malaysia where there are Authorised Merchants and/or Authorised Cash Outlets.
Commingling of Resold Services with Unbundled Network Elements and Combinations of Unbundled Network Elements 6.7.1 To the extent it is Technically Feasible and pursuant to the terms of Section 9.1, CLEC may Commingle Telecommunications Services purchased on a resale basis with an Unbundled Network Element or combination of Unbundled Network Elements.
Sale or License of Custom Products Involving Tax Exempt Financing (i.e., Certificates of Participation - COPS) The Authorized User’s sale or other transfer of Custom Products which were acquired by the Authorized User using third party, tax-exempt financing may not occur until such Custom Products are, or become, useable. In the event that the Contractor wishes to obtain ownership rights to Custom Product(s), the sale or other transfer shall be at fair market value determined at the time of such sale or other transfer, and must be pursuant to a separate written agreement in a form acceptable to the Authorized User which complies with the terms of this paragraph.
Scaling Lost Products The volume of lost products shall be determined by the best methods currently available, using data from the records for the period in which the loss occurred or the most applicable period if loss should occur substantially after cutting. In the absence of specific information indicating size or species of lost products, species distribution and volume for entire truckloads shall be assumed to be the same as the average volume Scaled per truck during the report period, and for individual products it shall be assumed that the volume and species were the average volume of the highest priced species Scaled during the report period. B6.851 Scaling Lost Sample Loads. If Scal- ing is being done by sampling loads of logs, Purchaser shall present such sample loads for Scaling by Forest Service. If loads of logs selected to be sample Scaled are placed in the decks before they are Scaled, they will be considered as lost sample loads. It will be difficult, if not impossible, to determine the volume and species con- tained in such loads for payment purposes. Therefore, lost sample loads will be deemed to have a Scale volume and species composition equal to that of the highest value load Scaled during the sampling period, as estab- lished by Forest Service. If no sample loads were Scaled during the period, the Scale data for the high valued load will be taken from the most current preceding sampling period with Scale. Sample loads lost as a result of Forest Service actions shall be treated as non-Scaled loads.
Other Products and Services As our customer, you have access to a suite of financial products and services availed by ourselves, our affiliates and strategic partners designed to help you address and achieve your financial needs and goals. You agree that you can obtain information about such Products and Services via our website xxx.xxxxxxxx.xxx.xx and you further agree that we can from time to time communicate information in relation to such Products or Services to you specifically or generally to all cardmembers via such communication mode as we consider appropriate.
PAYMENT FOR GOODS AND SERVICES a. DIR Customer shall comply with Chapter 2251, Texas Government Code, or applicable local law, in making payments to the Vendor. Payment under a DIR Contract shall not foreclose the right to recover wrongful payments.
New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.
