TANK Sample Clauses

TANK. 7.1 General Arrangement of LNG Tanks 26089-200-MT-1P24-00001 00D 7.2 Orientation and Schedule of Nozzles 26089-200-MT-1P24-00002 00D 7.3 Piles and Outer Tank Container 26089-200-MT-1P24-00003 00C 7.4 Corner Protection and Bottom Insulation 26089-200-MT-1P24-00004 00A 7.5 Suspended Deck and Wall Insulation 26089-200-MT-1P24-00005 00A 7.6 Pump Tube Arrangement 26089-200-MT-1P24-00006 00A 7.7 Inlet Piping and Cooldown Line 26089-200-MT-1P24-00007 00A 7.8 Foundation Heating 26089-200-MT-1P24-00008 00A 7.9 Temperature Sensor Locations 26089-200-MT-1P24-00009 00A 7.10 Spill Protection and Piping 26089-200-MT-1P24-00010 00B
View SourceView Similar (2)
TANK.  Transformer tank construction shallconform in allrespect to clause 15of IS1180(Part-1):2014.  Theinternalclearanceoftankshallbesuch,thatitshallfacilitateeasyliftingofcorewithcoilsfrom thetankwithoutdismantlingLVbushings.  Alljoints oftankandfittings shall be oiltightandnobulgingshouldoccur duringservice.  Inside oftankshall be paintedwith varnish/hotoil resistantpaint.  The topcoverofthetankshallbe slightly sloping todrainrainwater.  The tank plate and the lifting lugs shall be of such strength that the complete transformer filled with oil may be lifted by means of lifting shackle/Hook Type.  ManufacturershouldcarryoutallweldingoperationsaspertherelevantASMEstandardsand submitacopyoftheweldingprocedureandwelderperformancequalificationcertificatestothecustomer . i) PLAINTANK:
View Source
TANK. General Arrangement of LNG Tanks 26089-200-MT-1P24-00001 00D 7.2 Orientation and Schedule of Nozzles 26089-200-MT-1P24-00002 00D
View Source
TANK. The tank will be built with high strength structural steel sheets, reinforced with steel profiles. All the necessary openings on the walls of the tank and the cover will be provided with flanges welded to the tank, ready for use in packings, which will be made of elastic material, which do not deteriorate under the effect of hot oil. Oil resistant synthetic rubber packings will not be accepted. The tank will be provided with two earth sockets with their respective connectors located on the opposite ends of the bottom of the tank. The tank shall be fitted with the following valves and fittings (the list is not exhaustive), and if necessary, the manufacturer will implement the necessary accessories for the optimal operation of the reactor: i. Internal overpressure relief valve adjusted to 0.5 kg/cm2 of internal overpressure. ii. Connections valves for oil filtration, one located on top and the other at the bottom of the tank. iii. Three-way valve for connecting the connecting pipe to the ▇▇▇▇▇▇▇▇ relay. iv. Oil and purge intake valves.
View Source
TANK. The tank will be built with high strength structural steel sheets, reinforced with steel profiles. All the necessary openings on the walls of the tank and the cover will be provided with flanges welded to the tank, ready for use in packings, which will be made of elastic material, which do not deteriorate under the effect of hot oil. Oil resistant synthetic rubber packings will not be accepted. The tank will be provided with two earth sockets with their respective connectors located on the opposite ends of the bottom of the tank. Also, the tank shall be fitted with the following valves and fittings (the list is not exhaustive), and if necessary, the manufacturer will implement the necessary accessories for the optimal operation of the reactor: • Internal overpressure relief valve adjusted to 0.5 kg/cm2 of internal overpressure. • Connections valves for oil filtration, one located on top and the other at the bottom of the tank. • Three-way valve for connecting the connecting pipe to the ▇▇▇▇▇▇▇▇ relay. • Shut-off (separation) oil valves for each piping of the cooling system. • Oil and purge intake valves.
View Source

Related to TANK

  • Pipelines Developer shall have no interest in the pipeline gathering system, which gathering system shall remain the sole property of Operator or its Affiliates and shall be maintained at their sole cost and expense.

  • Storage Tanks If storage tanks storing Hazardous Materials located on the Premises or the Project are used by Tenant or are hereafter placed on the Premises or the Project by Tenant, Tenant shall install, use, monitor, operate, maintain, upgrade and manage such storage tanks, maintain appropriate records, obtain and maintain appropriate insurance, implement reporting procedures, properly close any storage tanks, and take or cause to be taken all other actions necessary or required under applicable state and federal Legal Requirements, as such now exists or may hereafter be adopted or amended in connection with the installation, use, maintenance, management, operation, upgrading and closure of such storage tanks. Notwithstanding anything to the contrary contained herein, Tenant shall have no right to use or install any underground storage tanks at the Project.

  • Underground Tanks If underground or other storage tanks storing Hazardous Materials located on the Premises or the Project are used by Tenant or are hereafter placed on the Premises or the Project by Tenant, Tenant shall install, use, monitor, operate, maintain, upgrade and manage such storage tanks, maintain appropriate records, obtain and maintain appropriate insurance, implement reporting procedures, properly close any underground storage tanks, and take or cause to be taken all other actions necessary or required under applicable state and federal Legal Requirements, as such now exists or may hereafter be adopted or amended in connection with the installation, use, maintenance, management, operation, upgrading and closure of such storage tanks.

  • Loading RPMG shall schedule the loading and shipping of all outbound corn oil purchased hereunder, but all labor and equipment necessary to load trucks and rail cars and other associated costs shall be supplied and borne by Producer without charge to RPMG. Producer shall handle the corn oil in a good and workmanlike manner in accordance with RPMG’s written requirements and normal industry practice. Producer shall maintain the truck and rail loading facilities in safe operating condition in accordance with normal industry standards and shall visually inspect all trucks and rail cars to assure (i) cleanliness so as to avoid contamination, and (ii) that such trucks and railcars are in a condition suitable for transporting the corn oil. RPMG and RPMG’s agents shall have adequate access to the Ethanol Facility to load Producer’s corn oil on an industry standard basis that allows RPMG to economically market Producer’s corn oil. RPMG’s employees shall follow all reasonable safety rules and procedures promulgated by Producer and provided to RPMG reasonably in advance and in writing. Producer shall supply product description tags, certificates of analysis, bills of lading and/or material safety data sheets that are applicable to all shipments. In the event that Producer fails to provide the labor, equipment and facilities necessary to meet RPMG’s loading schedule, Producer shall be responsible for all costs and expenses, including without limitation actual demurrage and wait time, incurred by RPMG resulting from or arising in connection with Producer’s failure to do so.

  • Storage The ordering agency is responsible for storage if the contractor delivers within the time required and the agency cannot accept delivery.