Site Specific Data of winter Season Sample Clauses

Site Specific Data of winter Season. This data shown that;  Average wind speed in the winter season was 2.9 m/sec and mostly the afternoon hours are windier. Maximum wind speed recorded was 3.9 m/sec.  Wind blows predominantly from North East (NE) to South West (SW) direction. Calm wind contributes to about 9.54% of all winds.  Average temperature recorded for winter season was 23.8°C with maximum temperature recorded as 29.3°C and minimum of 17.8°C.  The average relative humidity was 52.3% with maximum humidity recorded as 68.2% and minimum of 36.6%. The data obtained has been compiled to obtain average data. Compiled mean meteorological data is represented in Table 3-6. Table 3-6: Mean Meteorological Data of Dahej, Gujarat for Winter Season 2014-15 Hour Temperature (°C) Relative Humidity (%) Wind Speed (m/sec) Wind Direction Cloud Cover (Oktas) Rainfall (mm) 0.00 22.2 55.6 2.6 NE 3 0.0 1.00 21.4 57.0 2.4 NE 3 0.0 3.00 20.0 60.9 2.3 NE 3 0.0 4.00 19.3 63.4 2.1 NE 3 0.0 5.00 18.7 65.4 2.1 NE 3 0.0 6.00 18.2 67.0 2.0 NE 3 0.0 7.00 17.8 68.2 2.0 NE 3 0.0 8.00 18.8 67.3 2.4 NE 3 0.0 9.00 20.9 61.2 3.0 NE 3 0.0 10.00 23.3 54.2 3.3 NE 3 0.0 11.00 25.4 48.3 3.4 NE 3 0.0 12.00 27.1 43.0 3.6 E/NE/NW 3 0.0 13.00 28.1 40.8 3.7 N 3 0.0 14.00 28.6 40.5 3.9 NW 3 0.0 15.00 29.3 37.7 3.9 NW 3 0.0 16.00 29.1 36.6 3.9 NW 3 0.0 17.00 28.6 37.5 3.6 NW 3 0.0 18.00 27.4 41.6 3.0 NW 3 0.0 19.00 26.1 46.2 2.6 NW 3 0.0 20.00 25.2 49.3 2.8 N 3 0.0 Hour Temperature (°C) Relative Humidity (%) Wind Speed (m/sec) Wind Direction Cloud Cover (Oktas) Rainfall (mm) 21.00 24.4 52.2 3.1 N 3 0.0 22.00 23.7 53.7 2.6 NE 3 0.0 23.00 22.9 55.5 2.5 NE 3 0.0 Average 23.8 52.3 2.9 NE 3 0 Figure 3-2: Wind-rose Diagram of Winter Season 2014-15
Sample 1
AutoNDA by SimpleDocs

Related to Site Specific Data of winter Season

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • SS7 Network Interconnection 9.7.1 SS7 Network Interconnection is the interconnection of Global Connection local signaling transfer point switches or Global Connection local or tandem switching systems with BellSouth signaling transfer point switches. This interconnection provides connectivity that enables the exchange of SS7 messages among BellSouth switching systems and databases, Global Connection local or tandem switching systems, and other third-party switching systems directly connected to the XxxxXxxxx XX0 network.

  • Connecting Transmission Owner’s Scope of Work and Responsibilities The Connecting Transmission Owner will design, construct, own, operate and maintain all Connecting Transmission Owner’s Interconnection Facilities, except as otherwise stated above and in the Project Specific Specifications. The Connecting Transmission Owner will complete all engineering reviews, field verifications and witness testing, etc. in accordance with the ESBs and the Project Specific Specifications. Connecting Transmission Owner shall provide the revenue metering CT/PT units and meter socket enclosure. The Connecting Transmission Owner shall:  provide, run, and wire both ends of the color-coded cable for the revenue metering instrument transformer secondary wiring;  perform all terminations; and  supply and install the meter. The revenue meter may require a communications link to the RTU. The Connecting Transmission Owner will specify and run those communications cables. The Connecting Transmission Owner shall complete all wiring, testing and commissioning of the RTU.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Signaling Parameters All SS7 signaling parameters will be provided in conjunction with traffic exchange trunk groups, where and as available. These parameters include Automatic Number Identification ("ANI"), Calling Party Number ("CPN"), Privacy Indicator, calling party category information, originating line information, charge number, etc. Also included are all parameters relating to network signaling information, such as Carrier Information Parameter ("CIP"), wherever such information is needed for call routing or billing. GTE will provide SS7 via GR-394-SS7 and/or GR-317-SS7 format(s).

  • Escrow Format Specification 3.1. Deposit’s Format. Registry objects, such as domains, contacts, name servers, registrars, etc. will be compiled into a file constructed as described in draft-xxxxx-xxxxxxx-registry-data-escrow, see Part A, Section 9, reference 1 of this Specification and draft-xxxxx-xxxxxxx-dnrd-objects-mapping, see Part A, Section 9, reference 2 of this Specification (collectively, the “DNDE Specification”). The DNDE Specification describes some elements as optional; Registry Operator will include those elements in the Deposits if they are available. If not already an RFC, Registry Operator will use the most recent draft version of the DNDE Specification available at the Effective Date. Registry Operator may at its election use newer versions of the DNDE Specification after the Effective Date. Once the DNDE Specification is published as an RFC, Registry Operator will implement that version of the DNDE Specification, no later than one hundred eighty (180) calendar days after. UTF-8 character encoding will be used.

  • Schematic Design Phase Services § 3.2.1 The Architect shall review the program and other information furnished by the Owner, and shall review laws, codes, and regulations applicable to the Architect’s services.

  • Construction Phase Services 3.1.1 – Basic Construction Services

  • Service Specification The Parties have agreed upon the scope and specification of the Services provided under this Service Agreement in the Service Specification.

  • Technical Specification As enumerated in Special Conditions of Contract/Scope of Work/attached Drawing/ Details/Schedule of Rates.

Time is Money Join Law Insider Premium to draft better contracts faster.