Pilot House Remote Control Station Sample Clauses

Pilot House Remote Control Station. Each Pilot House remote control station shall include the following components:  Two (2) sets of identical controls, one (1) for each VSP or approved equal, consisting of: o One (1) thrust control joystick o One (1) 4-button modules for VSP or approved equal operation and control 670 functions including alarm indication, station transfer, standby pump, and active system selection. o One (1) 4-button module for engine speed selection as described in Section 252.2 above. 675 o One (1) 7-inch touch screen HMI display for display and control of bridge related propulsion system parameters, alarms and warnings.  Independent display of actual VSP or approved equal thrust position. The displays shall be LED bar graph indicators or similar, which clearly indicate actual longitudinal and transverse VSP or approved equal pitch. The independent displays shall be mounted forward of the control consoles, in the pilot's line of sight, generally where shown on 680 Reference (2M).  Coupling status indication, open/closed, for each fluid coupling  Emergency stop controls shall be provided as described in 252.5. Provide the ABS recommended and operationally required parts listed in Table 200 - 7 with the control systems and deliver as directed by the Owner's Representative. Quantities listed in Table 685 200 - 7 are per vessel. Table 200 - 7: Controls System ABS recommended and operationally required parts Qty Item 1 Bridge Display, 7 inches 1 EOS Display, 12 inches 2 Operating Unit, - Bedienstreifen 4-Taster
AutoNDA by SimpleDocs

Related to Pilot House Remote Control Station

  • Inventory Report – Remote Premises The locations of the Remote Premises (e.g., Feeder Distribution Interfaces, "FDI") and the End User Customer addresses served by each Remote Premises are available to CLEC through the Raw Loop Data Tool. Remote Premises with digital loop carrier and pair gain equipment will be provided on the web site in the ICONN database. (ICONN is available through the Qwest web site located at xxxx://xxx.xxxxx.xxx/iconn.) If CLEC is unable to determine the information it seeks regarding the Remote Premises after using such database tools, Qwest will provide CLEC with a report that contains the information. The Parties agree that a charge may apply to such report, based on time and material, unless the database information is inaccurate or unusable for the Remote Premises then no charge would apply. Qwest will provide CLEC access to relevant plats, maps, engineering records and other data in accordance with Section 10.8.2.4. In addition, CLEC can request a copy of Qwest's distribution area map associated with the Remote Premises, with a charge for time and material.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Required Coverages For Generation Resources Of 20 Megawatts Or Less Each Constructing Entity shall maintain the types of insurance as described in section 11.1 paragraphs (a) through (e) above in an amount sufficient to insure against all reasonably foreseeable direct liabilities given the size and nature of the generating equipment being interconnected, the interconnection itself, and the characteristics of the system to which the interconnection is made. Additional insurance may be required by the Interconnection Customer, as a function of owning and operating a Generating Facility. All insurance shall be procured from insurance companies rated “A-,” VII or better by AM Best and authorized to do business in a state or states in which the Interconnection Facilities are located. Failure to maintain required insurance shall be a Breach of the Interconnection Construction Service Agreement.

  • Information regarding Interconnection Facilities 4.2.1 The SPD shall be required to obtain all information from the STU/CTU/concerned authority with regard to the Interconnection Facilities as is reasonably necessary to enable it to design, install and operate all interconnection plant and apparatus on the SPD’s side of the Delivery Point to enable delivery of electricity at the Delivery Point. The transmission of power up to the point of interconnection where the metering is done for energy accounting shall be the responsibility of the SPD at his own cost.

  • Host-Remote When a CenturyLink Wire Center is served by a Remote Switch, CLEC may deliver traffic to the host Central Office or to the Tandem Switch. CLEC may not directly trunk to a Remote Switch. 7.2.2.10 Testing

  • Remote Work Remote work is the practice of performing required job functions from home or another management-approved location. Any employee who believes that all or part of their position is suitable for remote work may request to work remotely by submitting a written request to their supervisor. The Employer will evaluate the employee's request, and will approve or deny the request in writing. Employees whose requests to work remotely are approved may be required to sign an agreement confirming expectations regarding their schedule, timekeeping, remote work environment, data/information security and other matters specific to their position.

  • Compressed Work Week The Company and Union recognize the concept of the compressed work week. It is further understood that the compressed work week conditions will apply only to those departments that are on the compressed work week.

  • Remote Call Forwarding 4.2.10.1 As an option, BellSouth shall make available to CCI an unbundled port with Remote Call Forwarding capability (“URCF service”). URCF service combines the functionality of unbundled local switching, tandem switching and common transport to forward calls from the URCF service telephone number (the number dialed by the calling party) to another telephone number selected by the URCF service subscriber. When ordering URCF service, CCI will ensure that the following conditions are satisfied:

  • System Monitoring to ensure safe and continuous operation, the Customer must monitor key services and resource use as recommended by Deswik, and provide Deswik with details of monitoring and any relevant alerts as needed. Services to be monitors include, without limitation, disk space, CPU usage, memory usage, database connectivity, and network utilization.

  • Traffic Measurement and Billing over Interconnection Trunks 6.1 For billing purposes, each Party shall pass Calling Party Number (CPN) information on at least ninety-five percent (95%) of calls carried over the Interconnection Trunks.

Time is Money Join Law Insider Premium to draft better contracts faster.