PORTFOLIO HOLDINGS The Adviser will not disclose, in any manner whatsoever, any list of securities held by the Portfolio, except in accordance with the Portfolio’s portfolio holdings disclosure policy.
Percentages of ADB Financing 2. Except as ADB may otherwise agree, the items of the Categories listed in the Table shall be financed out of the proceeds of the Loan on the basis of the percentages set forth in the Table. Interest Charge
Creation/Acquisition of Subsidiaries In the event Borrower, or any of its Subsidiaries creates or acquires any Subsidiary, Borrower shall provide prior written notice to Collateral Agent and each Lender of the creation or acquisition of such new Subsidiary and take all such action as may be reasonably required by Collateral Agent or any Lender to cause each such Subsidiary to become a co-Borrower hereunder or to guarantee the Obligations of Borrower under the Loan Documents and, in each case, grant a continuing pledge and security interest in and to the assets of such Subsidiary (substantially as described on Exhibit A hereto); and Borrower (or its Subsidiary, as applicable) shall grant and pledge to Collateral Agent, for the ratable benefit of the Lenders, a perfected security interest in the Shares; provided, however, that solely in the circumstance in which Borrower or any Subsidiary creates or acquires a Foreign Subsidiary in an acquisition permitted by Section 7.7 hereof or otherwise approved by the Required Lenders, (i) such Foreign Subsidiary shall not be required to guarantee the Obligations of Borrower under the Loan Documents and grant a continuing pledge and security interest in and to the assets of such Foreign Subsidiary, and (ii) Borrower shall not be required to grant and pledge to Collateral Agent, for the ratable benefit of Lenders, a perfected security interest in more than sixty-five percent (65%) of the Shares of such Foreign Subsidiary, if Borrower demonstrates to the reasonable satisfaction of Collateral Agent that such Foreign Subsidiary providing such guarantee or pledge and security interest or Borrower providing a perfected security interest in more than sixty-five percent (65%) of the Shares would create a present and existing adverse tax consequence to Borrower under the U.S. Internal Revenue Code.
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Admission of the Corporate Taxpayer into a Consolidated Group; Transfers of Corporate Assets (a) If the Corporate Taxpayer is or becomes a member of an affiliated or consolidated group of corporations that files a consolidated income tax return pursuant to Sections 1501 et seq. of the Code or any corresponding provisions of state or local law, then: (i) the provisions of this Agreement shall be applied with respect to the group as a whole; and (ii) Tax Benefit Payments, Early Termination Payments and other applicable items hereunder shall be computed with reference to the consolidated taxable income of the group as a whole.
DOMESTIC PREFERENCES FOR PROCUREMENTS To the extent applicable, Supplier certifies that during the term of this Contract will comply with applicable requirements of 2 C.F.R. § 200.322.
Liquidations, Mergers, Consolidations, Acquisitions Each of the Loan Parties shall not, and shall not permit any of its Subsidiaries to, dissolve, liquidate or wind-up its affairs, or become a party to any merger or consolidation, or acquire by purchase, lease or otherwise all or substantially all of the assets or capital stock of any other Person, provided that
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
Other Financing Notwithstanding anything in this Agreement to the contrary, the Issuer and the Company may hereafter enter into agreements to provide for the financing or refinancing of costs of the Project or any portion thereof.
