Power Consumption Sample Clauses
POPULAR SAMPLE Copied 1 times
Power Consumption. The fidelity in modelling power consumption may vary. The average power regardless of mode could be represented (1), or the different power levels in each mode (2), or a varying power within each mode (3). Establishing the total power or energy consumption over an interval of time would then be treated differently in each case.
Alternative 1) would mean that the genericConstraintValue over all GenericConstraints with
Alternative 2) would mean that each unique mode assignment for the integrated architecture is traversed, and the genericConstraintValue over all GenericConstraints with genericConstraintType powerConsumption are multiplied by the time spent in this mode and added.
Alternative 3) would mean that simulation or analytical means are used to establish the instantaneous power in each component. Because power is allowed to vary, the component power must be defined by a function. Typically, power is related to the nominal functional behavior of the component. The genericConstraintValue for a powerConstraint could thus be an expression with nominal signals as operands. This is however not supported by EAST-ADL. The instant view of the power consumption can be used for integrating to energy consumption, averaging power levels for certain intervals, finding peak values, etc.
Power Consumption. The Building Management at B sites may be concerned about the power consumption of the WinStar equipment installed on their premises. By using Chart N, it is possible to evaluate the amount of AC power that will be used by various equipment configurations. To use the chart it is first necessary to calculate the DC requirement of the WinStar equipment - this will typically be 1.5 amps for each IDU/ODU and 0.6 amps for each Mux. Using this figure, the monthly AC power consumption can be found from the chart. The chart uses figures taken from the Lorain MZ10F50 Technical Document and assumes a 730 hour month. EQUIPPED B SITE GUIDELINES This phase of the B Site process will define the criteria for a fully equipped B Site Installation. EQUIPMENT STANDARD B SITE EQUIPMENT ORDERING FORMS Central Office Implementation updates the master equipment ordering forms and provides approved copies to construction and logistics to standardize equipment ordering. The following is an approved B Site equipment ordering form. Current Electronic Copies are available from Logistics and Central Office Implementation Standard Configuration 1 Build P-COM 8xT1 Link Power PART# MFG QTY ----------------------------------------------------------------------------------------------------- Rectifier, 10 Amp 486524401 Reltec 2 ----------------------------------------------------------------------------------------------------- Fan Module, Rectifier 427215600 Reltec 2 ----------------------------------------------------------------------------------------------------- Mounting Cabinet, Rectifier 588242000 Reltec 1 ----------------------------------------------------------------------------------------------------- Battery, 12V 100 Amp Sure Power 4 ----------------------------------------------------------------------------------------------------- Shelf, Battery 412805200 Reltec 1 ----------------------------------------------------------------------------------------------------- Power Strip IBAR-12 Tripplite 1 ----------------------------------------------------------------------------------------------------- Fuse Panel, Alarm 19"-23" ▇▇▇-▇▇▇▇-▇▇▇▇ Telect 1 ----------------------------------------------------------------------------------------------------- Mounts ----------------------------------------------------------------------------------------------------- Mounts: (one of following) 1 -----------------------------------------------------------------------------------------------...
Power Consumption. System consumes the maximum power @ 65°C with full traffic loading & all FAN runs at max. 25000RPM. The actual system power consumption will be calculated based on Beta verification data. Per system power estimation data, the switch board power consumption is around 240W with below configuration: timing interface & BMC works normally, 28x port SFP+ loopbacks with 1.5W power, 2x port QSFP28 loopback with 3.5W power, 6x DDR4 SDRAM packet buffer enabled, MAC & 10G,100G PHY runs at 300Gpbs traffic switching/forwarding, 5x FAN modules runs at 25000RPM. Measurement of existing ▇▇▇▇▇▇▇▇▇-DE CPU (4-core/2.2GHz) with 16GB SODIMM and 128GB SSD is 60W max. System total power consumption: 240 + 60W = Max. 300W To consider PSU efficiency 90% from -48V to +12V, overall system power requirement will be 300 / 0.9 = 333.3W.
2.3.1 Thermal Monitoring
Power Consumption. Based on minimum 7 watts per square foot (exclusive of HVAC equipment) of which 2 w▇▇▇▇ are at 120/208 volt and 3.5 watts allocated for lighting. ▇▇▇▇▇ption for cubicle installatio▇ ▇▇ 5 watts per 6 x 8 cubicle. LPT Standard Specifications
Power Consumption. Hotel shall provide at its sole cost electric power ----------------- supply suitable for the Service including recurring monthly charges to a maximum of Fifty Cents ($50/100) per installed guest and meeting rooms per month ($6.00 annual). Hotel reserves the right to charge Licensee for electrical usage in excess of such amount.
Power Consumption. The following tables list details of the power dissipation, weight, FITS and size for the TN-4XE equipment. TABLE 8-1 SUBRACK KEY SPECIFICATION DETAILS
Power Consumption. 51 12.3 Timing...................................................................................................52 12.3.1
Power Consumption. 1.9.1. Regarding the generated power consumption, priority needs to be given for internal consumption first and thereafter any excess power can be exported to the DISCOM network.
Power Consumption. The SSS shall not exceed the power consumption values listed in [**Redacted**]
Table 3.4.1-1 [**Redacted**] [**Redacted**] [**Redacted**]
Power Consumption. Liquidated damages of $1,370 per kW shall apply for every kW in excess of the guaranteed power consumption (excluding fan).