Common use of Commodity Specifications and Standards Clause in Contracts

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All The Representative Model, Required Aftermarket Options, OEM Options, and Identified Aftermarket Options are based on the available information known to the Department, including the known needs of Customers. Identified Aftermarket Options and Required Aftermarket Options listed in Exhibit B, Price Sheets (C.1 – C.6) were created based on known Customer needs and the respective Manufacturer’s data. The Contract specifications and standards form a part of the overall specifications for the listed Representative Models, except as modified or noted herein. Any conflict between the Department’s Contract specifications and standards and the Manufacturer’s specifications will be resolved in favor of the Department specifications and standards. The Contractor shall ensure that all Commodities, including all Base EquipmentRepresentative Models, OEM and Non-OEM Options, Required Aftermarket Option(s) (where applicable), Identified Aftermarket Option(s), Part(s), Accessory(ies), and Implement(s); and their the respective features, devices, equipment, and components, shall meet individually and jointly comply with the following minimum requirementsfollowing: 1. a. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by service per the Customer unless specifically agreed to by the Customer and ContractorScope of Work; 2. b. All Commodities shall be new and unused (except as specified in the Transportation and Delivery sectionsection of the Scope of Work), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. c. All Commodities shall be biodiesel bio-diesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered.; 4. d. All Commodities shall include all OEM Option standard features, equipment, and components, components installed by Manufacturer or Dealer installed according to the Manufacturer’s current standard procedures, requirements, and specifications; 5. e. All Commodities shall meet the Automatic Air Brake Drain System Specifications; f. All Commodities shall be free of damage damage, defect, and / or rust which may affect appearance appearance, operability, functionality, or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. g. All Commodities shall comply with required state current legal, customary, reasonable, and professional standards of the motor vehicle and mobile equipment industry; h. All Commodities shall comply with current mandatory and applicable federal lawsand State of Florida Motor Vehicles requirements including, including but not limited to: motor vehicle, mobile equipmentall legal, safety, and environmental lawsstandards and requirements; and 8. i. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor No Contractor’s or Dealer Dealer’s advertising or identification (name, logos, etc.) is permitted on the Commodities, including Base Equipmentall Representative Models, OEM and Non-OEM Option(s)Options, Part(s)Identified Aftermarket Options, Accessory(ies)Required Aftermarket Options, and Implement(s); Accessories, Replacement Parts and their respective features, equipment, and components. Manufacturer Commodity Manufacturer’s advertising or identification (name, model, logos, etc.) shall be is permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all impermissible or unacceptable advertising or identification. The Contractor may engage Dealers Department reserves the right to, in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contractits sole discretion, determine what advertising or identification is considered unacceptable. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms Delivery of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized non-conforming Commodities and MSRP List. The Contractor shall remain responsible contractual services, which are not remedied as required herein, may be cause for receiving purchase orders default proceedings and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇Contract termination.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All The Contractor shall ensure that all Commodities, including all Base Equipment, OEM and Non-OEM Option(s)Options, Part(s)Parts, Accessory(ies)Accessories, and Implement(s); Implements, and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery sectionsection in this SOW), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery sectionsection of this SOW), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered.; 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or and/or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: to motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s)Options, Part(s)Parts, Accessory(ies)Accessories, and Implement(s); Implements, and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage use Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_formssubco ntractor_dealer_reseller_forms.

Commodity Specifications and Standards. The Commodity Specifications and Standards are based on the known needs of Eligible Users and best information available to the Department at the time the Commodity Specifications and Standards were created. The following specifications and standards form a part of the overall Technical Specifications except as modified or noted herein. All Commodities, including all Base Equipment; OEM Options, Accessories, & Implements; OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s)& Replacement Parts; and their respective features, equipment, and components, shall meet individually and jointly comply with the following minimum requirementsfollowing: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Section 3.9, Transportation and Delivery sectionDelivery), and installed (OEM & Replacement Parts do not include installation) to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Section 3.9, Transportation and Delivery sectionDelivery), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel bio-diesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered.; 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designedcomply with current legal, manufacturedcustomary, installedreasonable, and serviced pursuant to prudent standards of professionalism and care in the industry standard of careindustry; 7. All Commodities shall comply with required state current mandatory and applicable federal laws, including but not limited to: and State of Florida motor vehicle, mobile equipment, legal, safety, and environmental lawsstandards and requirements; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor No Contractor’s or Dealer Dealer’s advertising or identification (name, logos, etc.) is permitted on the Commodities, including all Base Equipment; OEM Options, Accessories, & Implements; OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s)& Replacement Parts; and their respective features, equipment, and components. Manufacturer Commodity Manufacturer’s advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, Department in its sole discretion, discretion shall determine what is Contractor Contractor’s or Dealer Dealer’s advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms Delivery of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized non-conforming Commodities and MSRP List. The Contractor shall remain responsible contractual services, which are not remedied as required herein, may be cause for receiving purchase orders default proceedings and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇/ or Contract termination.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All The Base Vehicle Specifications and Options are based on the available information known to the Department at the time of the solicitation, including the known needs of Customers and information obtained using Autodata, Inc. d/b/a Chrome Data’s Carbook Pro Fleet Edition. Options listed in Exhibit B, Price Sheet (C.4) were identified based on known Customer needs and the respective Manufacturer’s data. The Contract specifications and standards form a part of the overall specifications for the listed Representative Models, except as modified or noted herein. Any conflict between the Department’s Contract specifications and standards and the Manufacturer’s specifications will be resolved in favor of the Department specifications and standards. The Contractor shall ensure that all Commodities, including all Base EquipmentRepresentative Models, OEM and Non-OEM Option(s), Part(s), Accessory(ies)Options, and Implement(s); and their the respective featuresComponents, equipmentFeatures, and componentsor Configurations, shall meet individually and jointly comply with the following minimum requirementsfollowing: 1. a. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section)assembled, and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by service per the Customer unless specifically agreed to by the Customer and ContractorScope of Work; 2. b. All Commodities shall be new and unused (except as specified in the Transportation and Delivery sectionsection of the Scope of Work), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. c. All Commodities Representative Models shall be biodiesel diesel powered. choices for alternative fuel fuels (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered) can be listed for reference and customer selection if desired. 4. d. All Commodities shall include all OEM Option standard features, equipment, and components, components installed by Manufacturer or Dealer installed according to the Manufacturer’s current standard procedures, requirements, and specifications; 5. e. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities Representative Models shall meet the requirementsAutomatic Air Brake Drain System Specifications, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found which are available at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/content/state_purchasingdownload/ 152586/1015180/vendor_resourcesfile/s ubcontractor_dealer_reseller_formsAIRBRAKE.pdf; f. All Commodities shall be free of damage, defect, and rust which may affect appearance, operability, functionality, or serviceability; g. All Commodities shall comply with current legal, customary, reasonable, and professional standards of the Medium and Heavy Trucks industry; h. All Commodities shall comply with current mandatory and applicable federal and State Medium and Heavy Trucks requirements including, but not limited to, all legal, safety, and environmental standards and requirements; and i. All Commodities shall meet the requirements, specifications, terms, and conditions herein. No Contractor’s or Dealer’s advertising or identification (name, logos, etc.) is permitted on the Commodities, including all Representative Models and Options and their components. Commodity Manufacturer’s advertising or identification (name, model, logos, etc.) is permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Contractor shall be responsible for removing, without damage, all impermissible or unacceptable advertising or identification. The Department reserves the right to, in its sole discretion, determine what advertising or identification is considered unacceptable. Delivery of non-conforming Commodities and contractual services, which are not remedied as required herein, may be cause for default proceedings and Contract termination.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: F3E6A3C5-71E8-4CD4-A63A-0D8A90091493 Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: 25D680E7-2C87-406F-9F00-FF0149CC0FF5 Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: 58B992CD-DCA0-4DED-A644-E3AA202A0B4E Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All The Contractor shall ensure that all Commodities, including all Base Equipment, OEM and Non-OEM Option(s)Options, Part(s)Parts, Accessory(ies)Accessories, and Implement(s); Implements, and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery sectionsection in this SOW), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery sectionsection of this SOW), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered.; 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or and/or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: to motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s)Options, Part(s)Parts, Accessory(ies)Accessories, and Implement(s); Implements, and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: 3827635E-4E89-402F-9F7D-A883C68EF862 Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. The Commodity Specifications and Standards are based on the known needs of Eligible Users and best information available to the Department at the time the Commodity Specifications and Standards were created. The following specifications and standards form a part of the overall Technical Specifications except as modified or noted herein. All Commodities, including all Base Equipment; OEM Options, Accessories, & Implements; OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s)& Replacement Parts; and their respective features, equipment, and components, shall meet individually and jointly comply with the following minimum requirementsfollowing: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the section 3.9, Transportation and Delivery sectionDelivery), and installed (OEM & Replacement Parts do not include installation) to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the section 3.9, Transportation and Delivery sectionDelivery), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel bio-diesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered.; 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designedcomply with current legal, manufacturedcustomary, installedreasonable, and serviced pursuant to prudent standards of professionalism and care in the industry standard of careindustry; 7. All Commodities shall comply with required state current mandatory and applicable federal laws, including but not limited to: and State of Florida motor vehicle, mobile equipment, legal, safety, and environmental lawsstandards and requirements; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor No Contractor’s or Dealer Dealer’s advertising or identification (name, logos, etc.) is permitted on the Commodities, including all Base Equipment; OEM Options, Accessories, & Implements; OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s)& Replacement Parts; and their respective features, equipment, and components. Manufacturer Commodity Manufacturer’s advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, Department in its sole discretion, discretion shall determine what is Contractor Contractor’s or Dealer Dealer’s advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms Delivery of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized non-conforming Commodities and MSRP List. The Contractor shall remain responsible contractual services, which are not remedied as required herein, may be cause for receiving purchase orders default proceedings and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇/ or Contract termination.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: 357AD5A2-BD41-424B-A705-8967AF2DF5BD Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The DocuSign Envelope ID: 0C526FA5-FA0B-4745-8EA8-EEEFB481AF12 Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.

Commodity Specifications and Standards. All Commodities, including all Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components, shall meet the following minimum requirements: 1. All Commodities shall be designed, constructed, equipped, assembled (except as specified in the Transportation and Delivery section), and installed to be fully suitable for their intended use, purpose, and service. The Contractor is not required to install Parts purchased by the Customer unless specifically agreed to by the Customer and Contractor; 2. All Commodities shall be new and unused (except as specified in the Transportation and Delivery section), for the current Manufacturer’s model year or later, of current or recent production, and of the latest design and construction; 3. All Commodities shall be biodiesel (B-20), compressed natural gas (“CNG”), diesel, electric, gasoline (E-10 to E-85), liquefied petroleum gas (“LPG”), natural gas, or propane powered. 4. All Commodities shall include all OEM standard features, equipment, and components, Manufacturer or Dealer installed according to the Manufacturer’s standard procedures, requirements, and specifications; 5. All Commodities shall be free of damage and / or rust which may affect appearance or serviceability; 6. All Commodities shall be professionally designed, manufactured, installed, and serviced pursuant to the industry standard of care; 7. All Commodities shall comply with required state and federal laws, including but not limited to: motor vehicle, mobile equipment, safety, and environmental laws; and 8. All Commodities shall meet the requirements, specifications, terms, and conditions herein. Contactor shall ensure that no Contractor or Dealer advertising or identification (name, logos, etc.) is on the Commodities, including Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components. Manufacturer advertising or identification (name, model, logos, etc.) shall be permitted on the respective Commodities if such advertising or identification is a Manufacturer’s standard on the specific Commodity. The Department, in its sole discretion, shall determine what is Contractor or Dealer advertising or identification, what is Commodity Manufacturer’s advertising or identification, and what advertising or identification is acceptable. The Contractor shall be responsible for removing, without damage, all unacceptable advertising or identification. The Contractor may engage Dealers in accordance with the terms herein to provide sales and support for the awarded Commodities offered under this Contract. In the event the Contractor elects to use Dealers, the Contractor shall remain fully accountable for ensuring that the Dealer complies with the terms of this Contract. In the event the Dealers fail to comply with the terms of this Contract, the Contractor shall remain fully liable. The Contractor shall ensure that Dealers remain current with the Contractor’s authorized Commodities and MSRP List. The Contractor shall remain responsible for receiving purchase orders and shall remain responsible for invoicing the Customer for payment. All invoices shall remain in the name of the Contractor. The Contractor may not utilize Dealers until receiving express authorization from the Department. Information regarding the Contractor’s addition of Dealers can be found at the following link: ▇▇▇▇▇://▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇.▇▇▇/business_operations/state_purchasing/vendor_resources/s ubcontractor_dealer_reseller_forms.