Baseplates Clause Samples

Baseplates. A. All baseplates and anchors on Platforms shall: 1. be minimized; and
Baseplates. Clean concrete-bearing surfaces of bond-reducing materials, and roughen surfaces prior to setting plates. Clean bottom surface of plates. 1. Set plates for structural members on wedges, shims, or setting nuts as required. 2. Weld plate washers to top of baseplate. 3. Snug-tighten anchor rods after supported members have been positioned and plumbed. Do not remove wedges or shims but, if protruding, cut off flush with edge of plate before packing with grout. 4. Promptly pack shrinkage-resistant grout solidly between bearing surfaces and plates, so no voids remain. Neatly finish exposed surfaces; protect grout and allow to cure. Comply with manufacturer's written installation instructions for grouting.
Baseplates. A. All baseplates and anchors on Platforms, except for those for Passenger Interface Equipment, shall: 1. be encased in cast-in-place concrete surrounds with chamfered corners that: a. are minimum 150 mm and maximum of 300 mm high; and b. extend no more than 175 mm from each face of the structure being supported by the baseplate; and 2. not present a tripping hazard.
Baseplates. Clean concrete- and masonry-bearing surfaces of bond-reducing materials, and roughen surfaces prior to setting plates. Clean bottom surface of plates.

Related to Baseplates

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Integration The Company shall not sell, offer for sale or solicit offers to buy or otherwise negotiate in respect of any security (as defined in Section 2 of the Securities Act) that would be integrated with the offer or sale of the Securities for purposes of the rules and regulations of any Trading Market such that it would require shareholder approval prior to the closing of such other transaction unless shareholder approval is obtained before the closing of such subsequent transaction.

  • Assembly (a) The Contracting Parties shall have an Assembly. (b) Each Contracting Party shall be represented by one delegate who may be assisted by alternate delegates, advisors and experts. (c) The expenses of each delegation shall be borne by the Contracting Party that has appointed the delegation. The Assembly may ask WIPO to grant financial assistance to facilitate the participation of delegations of Contracting Parties that are regarded as developing countries in conformity with the established practice of the General Assembly of the United Nations or that are countries in transition to a market economy. (a) The Assembly shall deal with matters concerning the maintenance and development of this Treaty and the application and operation of this Treaty. (b) The Assembly shall perform the function allocated to it under Article 26(2) in respect of the admission of certain intergovernmental organizations to become party to this Treaty. (c) The Assembly shall decide the convocation of any diplomatic conference for the revision of this Treaty and give the necessary instructions to the Director General of WIPO for the preparation of such diplomatic conference. (a) Each Contracting Party that is a State shall have one vote and shall vote only in its own name. (b) Any Contracting Party that is an intergovernmental organization may participate in the vote, in place of its Member States, with a number of votes equal to the number of its Member States which are party to this Treaty. No such intergovernmental organization shall participate in the vote if any one of its Member States exercises its right to vote and vice versa. (4) The Assembly shall meet in ordinary session once every two years upon convocation by the Director General of WIPO. (5) The Assembly shall establish its own rules of procedure, including the convocation of extraordinary sessions, the requirements of a quorum and, subject to the provisions of this Treaty, the required majority for various kinds of decisions.

  • Architecture The Private Improvements shall have architectural features, detailing, and design elements in accordance with the Project Schematic Drawings. All accessory screening walls or fences, if necessary, shall use similar primary material, color, and detailing as on the Private Improvements.

  • Fabrication Making up data or results and recording or reporting them.