Amendments and Publication of Compliance Procedure. This Compliance Procedure may be amended from time-to-time by the Authority. Copies of this Compliance Procedure and any amendments will be included in the permanent records of the Authority.
Amendments and Publication of Compliance Procedure Sample Clauses
Related to Amendments and Publication of Compliance Procedure
RECEIPT AND PUBLICATION OF NOTICES 11.1 Immediately after it receives a demand or notice from any Noteholder in accordance with the Conditions, the Agent shall forward a copy to the Issuer.
NOTIFICATION OF PUBLIC EVENTS AND MEETINGS 2 A. CONTRACTOR shall notify ADMINISTRATOR of any public event or meeting funded in 3 whole or in part by the COUNTY, except for those events or meetings that are intended solely to serve 4 clients or occur in the normal course of business.
Notification and Public Notice If either party desires to alter or amend this Agreement, it shall, not less than one hundred and twenty (120) days prior to the termination date set forth under the Duration Article, provide written notice and a proposal to the other party of said desire and the nature of the amendments, and cause the public notice provisions of law to be fulfilled.
DECLARATION OF COMPLIANCE WITH APPLICABLE STANDARDS 1. Does the Work report experiments involving human subjects? [ ] YES [ ] NO If Yes, were the reported experiments in accordance with the ethical standards of the committee responsible for human experimentation (institutional and national), and with the Helsinki Declaration of 1975, as revised in 2013 (xxxx://xxxxxx.xxx.xxx/ecodes/node/3931 )? [ ] YES [ ] NO (If Yes, the Assignor must submit a copy of the approval and consent-to-disclose form to Xxxxxxx Science Publishers by fax or email.) Please state whether Ethical Approval was given, by whom and the relevant Judgement’s reference number. (If No, the Assignor must mention an institutional or regional guideline.) 2. Does the Work report experiments involving animals? [ ] YES [ ] NO If Yes, were the reported experiments in accordance with the standards set forth in one of below national guidelines and regulations: o The US National Research Council's "Guide for the Care and Use of Laboratory Animals," o The US Public Health Service's "Policy on Humane Care and Use of Laboratory Animals," and "Guide for the Care and Use of Laboratory Animals." o UK : the Animals (Scientific Procedures) Act 1986 Amendment Regulations (SI 2012/3039). [ ] YES [ ] NO 6 [v.122016] CONFLICTS OF INTEREST Conflicts of interest arise when authors, reviewers, or editors have interests (such as financial or personal interests) that are not made clear and that may influence their judgment on the content of their work. Authors and editors who submit work for publication with Xxxxxxx Science are required to disclose and acknowledge all forms of financial support relating to the work to be published, all commercial or financial involvement that might present an appearance of a conflict of interest in respect of the work, and all agreements relating to sponsorship of any research upon which the work is based. Are there any actual, or potential, conflicts of interest? [ ] YES [ ] NO If Yes, details of the actual or potential conflicts of interest must be set-out in the spaces provided below. DISCLOSURE REGARDING ACTUAL OR POTENTIAL CONFLICTS OF INTEREST: [INSERT] DISCLOSURE REGARDING THIRD PARTY FINANCIAL CONTRIBUTIONS: [INSERT] LANGUAGE AND EDITING: Does Assignor require assistance in having the English grammar and style of the Work checked and improved by Xxxxxxx Science? [ ] YES [ ] NO If Yes, Xxxxxxx Science will provide a quote in respect of the same.
Information and Publicity 1. The LP undertakes to fulfil the information and publicity measures set out in Commission Regulation (EC) No. 1303/2013, and in the information and publicity guidelines included the Implementation Manual, the Visual Identity Manual for projects and the Communication toolkit of the Danube Transnational Programme with the aim to promote the fact that financing is provided from the European Union Funds in the framework of the Danube Transnational Programme and to ensure the adequate promotion of the project.
PUBLICATION AND PUBLICITY The CONSULTANT agrees that it shall not for any reason whatsoever communicate to any third party in any manner whatsoever concerning any of its CONTRACT work product, its conduct under the CONTRACT, the results or data gathered or processed under this CONTRACT, which includes, but is not limited to, reports, computer information and access, drawings, studies, notes, maps and other data prepared by and for the CONSULTANT under the terms of this CONTRACT, without prior written approval from the COMMISSION, unless such release or disclosure is required by judicial proceeding. The CONSULTANT agrees that it shall immediately refer any third party who requests such information to the COMMISSION and shall also report to the COMMISSION any such third party inquiry. This Article shall not apply to information in whatever form that comes into the public domain, nor shall it restrict the CONSULTANT from giving notices required by law or complying with an order to provide information or data when such order is issued by a court, administrative agency or other authority with proper jurisdiction, or if it is reasonably necessary for the CONSULTANT to defend itself from any suit or claim. All approved releases of information, findings, and recommendations shall include a disclaimer provision and all published reports shall include that disclaimer on the cover and title page in the following form: The opinions, findings, and conclusions in this publication are those of the author(s) and not necessarily those of the Mississippi Department of Transportation, Mississippi Transportation Commission, the State of Mississippi or the Federal Highway Administration.
Ownership and Publication of Materials All reports, information, data, and other materials prepared by the Consultant pursuant to this agreement are the property of the City. The City has the exclusive and unrestricted authority to release, publish or otherwise use, in whole or part, information relating thereto. Any re-use without written verification or adaptation by the Consultant for the specific purpose intended will be at the City’s sole risk and without liability or legal exposure to the Consultant. No material produced in whole or in part under this agreement may be copyrighted or patented in the United States or in any other country without the prior written approval of the City.
COMPLETION OF MEET AND NEGOTIATION 24.1 During the term of this Agreement, the Association expressly waives and relinquishes the right to meet and negotiate and agrees that the District shall not be obligated to meet and negotiate with respect to any subject or matter whether referred to or covered in this Agreement or not, even though each subject or matters may not have been within the knowledge or contemplation of either or both the District or the Association at the time they met and negotiated on and executed this Agreement, and even though such subjects or matters were proposed and later withdrawn.
PUBLIC RELATIONS AND PUBLICITY 43.1 The Provider must not by itself, its employees or agents and procure that its Sub-Contractors must:
Certification of Compliance The Owner may permit the use, prior to sampling and testing, of certain materials or assemblies when accompanied by manufacturer's certificates of compliance stating that such materials or assemblies fully comply with the requirements of the contract. The certificate shall be signed by the manufacturer. Each lot of such materials or assemblies delivered to the work must be accompanied by a certificate of compliance in which the lot is clearly identified. Materials or assemblies used on the basis of certificates of compliance may be sampled and tested at any time and if found not to be in conformity with contract requirements will be subject to rejection whether in place or not. The form and distribution of certificates of compliance shall be as approved by the Owner. When a material or assembly is specified by "brand name or equal" and the Contractor elects to furnish the specified "brand name", the Contractor shall be required to furnish the manufacturer's certificate of compliance for each lot of such material or assembly delivered to the work. Such certificate of compliance shall clearly identify each lot delivered and shall certify as to:
