726 Total Sample Clauses

726 Total. Work Responsibility Barcelona Prototype: dummy sensor, production procurement (part) Bonn AgSn vendor qualification, production procurement (part) KEK production procurement (part) CERN Measurements on prototypes, production procurement (part) Milano Indium vendor qualification, production procurement (part) Cost Sharing: Prototype Production Total % % % Barcelona (E) 20% 10% 11% Bonn (D-BMBF) 40% 50% 49% CERN - 15% 14% KEK (J) - 15% 14% Milano (I) 40% 10% 13% Unassigned - - - Total 100% 100% 100% Note: In the prototype phase the cost of FE-I4 wafer thinning and bump-deposition are in MoU item #3. The sensor wafer processing (UBM/bump-deposition) and flip chip is in MoU item #1. Qualify the two vendors used by ATLAS Pixel - baseline AgSn - Technology backup Indium. KEK develops bump-bonding R&D with Hamamatsu for sLHC (will become an option for IBL if the other fail), participation to common procurement. MoU Item 4 Annex 1
AutoNDA by SimpleDocs

Related to 726 Total

  • Total 1 Nationality: country to which the person belongs administratively and that issues the ID card and/or passport.

  • Subtotal (h) Add Bond and Insurance, not to exceed percent ( %) of Item (g)

  • CFR 200 328. Failure to submit such required Performance Reports may cause a delay or suspension of funding. 30 ILCS 705/1 et seq.

  • Bilingual Differential When formally assigned in the employee’s position description, an employee assigned to interpret to or from another language to English will receive a differential of five percent (5%) of base pay.

  • WSIB Top-Up a) Teachers who, as of August 31, 2014, were entitled to Workplace Safety and Insurance Board benefits top-up, such entitlement shall be as follows:

  • Bilingual Differential Pay Bilingual Differential Pay applies to those positions designated by the Department of Personnel Administration as eligible to receive bilingual pay according to the following standards:

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Step 4 In the event the dispute is not resolved at Step 3 above, either party may serve upon the other and the COORDINATOR written notice by certified mail, within five (5) working days, requesting that the dispute be resolved by arbitration. If such a written notice is served, the parties shall jointly request the Federal Mediation and Conciliation Service to submit the names of five (5) qualified arbitrators, from which list the UNION and the EMPLOYER shall alternately strike names until only one name is left, which person shall hear and resolve the dispute. A hearing shall be conducted by the arbitrator, at which time the parties to the dispute shall be given the opportunity to appear and offer evidence in support of their positions. A decision by the arbitrator shall be rendered in writing within a reasonable time, not to exceed ten (10) days after the conclusion of the hearing. The decision by the arbitrator shall be final and binding upon the parties; provided, however, that the arbitrator shall not have the authority to alter or amend the provisions of this AGREEMENT in any way. The reasonable expenses and fees of the arbitrator shall be borne equally by the parties.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Orthodontia lifetime maximum Orthodontia benefits are subject to a three thousand dollar ($3,000) lifetime maximum benefit.

Time is Money Join Law Insider Premium to draft better contracts faster.