Touchup coating definition

Touchup coating means a coating used to cover minor coating imperfections appearing after the main coating operation.
Sample 1Sample 2Sample 3

Examples of Touchup coating in a sentence

  • Touch-up coating and surface preparations shall be in addition to and not considered as the first field coat.

  • Touch-up coating operations as defined in Section IV.KK, not exceeding nine square feet per vehicle.

  • Touch-up coating to be done for areas damaged during erection, or areas not pre-coated.

  • Touch-up coating shall be done per the manufacturer's recommendations where needed and as directed to achieve 100% holiday-free surface.

  • Touch-up coating shall overlap the prime, intermediate and finish coats by not less than one inch all around to ensure continuity of coating.xlvii.

  • Touch-up coating In touch-up coating only parts of the structure and coating system are recoated.

  • Touchup coating shall be done in accordance with manufacturer's recommendations.

  • R002, Touch-up coating booth14 Authorization Facility ID: 0857083299Application Number(s): A0036961 Permit Number: P0104452Permit Description: First issue PTIO for honeycomb coating tank with curing oven (R001) and touch up coating booth (R002) after PTI 08-04836.Permit Type: Renewal Permit Fee: $0.00 Issue Date: 3/23/2009Effective Date: 3/23/2009 Expiration Date: 3/23/2019Permit Evaluation Report (PER) Annual Date: Jan 1 - Dec 31, Due Feb 15This document constitutes issuance to: ATK Space Systems, Inc.

  • Touch-up coating shall be done for areas damaged during erection, or areas not pre­ coated.

  • Touch-up coating, with a maximum aerosol coating usage rate of 0.078 gallons per hour, with particulate emissions controlled using downdraft tables equipped with particulate filtration systems, and exhausting inside the building.

Related to Touchup coating

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Flat coating means a coating that is not defined under any other definition in this section and that registers gloss less than 15 on an 85-degree meter or less than 5 on a 60-degree meter.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Undercoating means any aerosol product designed to impart a protective, non-paint layer to the undercarriage, trunk interior, and/or firewall of motor vehicles to prevent the formation of rust or to deaden sound. “Undercoating” includes, but is not limited to, rubberized, mastic, or asphaltic products.

  • Metallic coating means a coating which contains more than five grams of metal particles per liter of coating, as applied. Metal particles are pieces of a pure elemental metal or a combination of elemental metals.

  • Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, and stains.

  • Clear coating means a transparent coating designed to provide the final gloss and resistance properties of the coating system;

  • Dip coating means the application of a coating material to a substrate by dipping the part into a tank of the coating material.

  • Basecoat means a coat of colored material, usually opaque, that is applied before graining inks, glazing coats, or other opaque finishing materials and is usually topcoated for protection.

  • Floor coating means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces which may be subject to foot traffic.

  • Nuclear coating means any protective coating used to seal porous surfaces, such as steel or concrete, that otherwise would be subject to intrusion by radioactive materials. These coatings must be resistant to long term (service life) cumulative radiation exposure (ASTM D4082-83**), relatively easy to decontaminate (ASTM D4256-83**), and resistant to various chemicals to which the coatings are likely to be exposed (ASTM 3912-80**). General protective requirements are outlined by the Department of Energy (formerly United States Atomic Energy Commission Regulatory Guide 1.54**).

  • Faux finishing coating means a coating labeled and formulated as a stain or a glaze to create artistic effects including, but not limited to, dirt, old age, smoke damage, and simulated marble and wood grain.

  • Roll coating means the application of a coating material to a substrate by means of hard rubber or steel rolls.

  • Topcoat means a coating that is applied over a primer on an aerospace vehicle or component for appearance, identification, camouflage, or protection. Topcoats that are defined as specialty coatings are not included under this definition.

  • Seaplane means an aeroplane capable normally of taking off from and alighting solely on water;

  • Furniture coating means any paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

  • Flow coating means a coating labeled and formulated exclusively for use by electric power companies or their subcontractors to maintain the protective coating systems present on utility transformer units.

  • Specialty coating means any coating that is manufactured and used for one (1) of the following specialized applications:

  • Pretreatment coating means a coating which contains no more than 12% solids by weight, and at least 0.5% acid by weight, is used to provide surface etching, and is applied directly to metal surfaces to provide corrosion resistance, adhesion, and ease of stripping.

  • Clone means a non-flowering plant cut from a mother plant that is capable of developing into a new plant and has shown no signs of flowering.

  • Edge of any water means the outer edge of the water's bankfull width or, where applicable, the outer edge of the associated channel migration zone.

  • Falconry means the sport of taking quarry by means of a trained raptor.

  • Automotive windshield washer fluid means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

  • Spirits means any beverage which contains alcohol obtained by distillation mixed with drinkable water and other substances in solution, including, but not limited to, brandy, rum, whisky, and gin.

  • Repair coating means a coating used to re-coat portions of a previously coated product which has sustained mechanical damage to the coating following normal coating operations.

  • Low-solids coating means a coating containing 0.12 kilogram or less of solids per liter (one pound or less of solids per gallon) of coating material.