Photometric measurements definition

Photometric measurements means the measurements of luminance levels made on the face of the sign.

Examples of Photometric measurements in a sentence

  • Photometric measurements shall be carried out on the samples before and after the test.

  • Photometric measurements shall be performed according to the applicant's description: 5.3.1.4.1. At neutral state; 5.3.1.4.2. At V-signal, W-signal, E-signal, T-signal whichever apply; 5.3.1.4.3. If applicable, at any other signal(s) and combinations of them, according to the applicant's specification.

  • Photometric measurements at 100 hours, 1,000 hours, and 40% of rated life.

  • Photometric measurements need to be acquired at a time when the light output of the lamp has reached a steady state.

  • Photometric measurements were made at approximately 510 nm against the reagent blank.

  • Should be compliant to LM79 IESNA: Approved method for the electrical and Photometric measurements of Solid-state lighting products.

  • At the motion hearing, however, Wife testified that she had attempted to enroll in only one class during the year-and-a-half time period between the amended final decree and the motion hearing.

  • Photometric measurements were made at approximately 525 nm against the reagent blank.

  • Photometric measurements were made at approximately 610 nm against distilled water as a reagent blank.

  • Figure 1.Calibration curve of Mn. Photometric Figure 2.Calibration curve of Fe. Photometric measurements were made at 525 nm measurements were made at 510 nm Figure 3.

Related to Photometric measurements

  • COVID-19 Measures means any quarantine, “shelter in place,” “stay at home,” workforce reduction, social distancing, shut down, closure, sequester or any other Law, directive, guidelines or recommendations by any Governmental Authority (including the Centers for Disease Control and the World Health Organization) in each case in connection with, related to or in response to COVID-19, including the Coronavirus Aid, Relief, and Economic Security Act (CARES) or any changes thereto.

  • Instantaneous flow measurement means the flow measured during the minimum time required for the flow-measuring device or method to produce a result in that instance. To the extent practical, instantaneous flow measurements coincide with the collection of any grab samples required for the same sampling period so that together the samples and flow are representative of the discharge during that sampling period.

  • Supportive measures means individualized services that are offered to the complainant or the respondent designed to restore or preserve equal access to the District’s education program or activity without unreasonably burdening the other party. The supportive measures must be non-disciplinary and non-punitive in nature; offered before or after the filing of a formal complaint or where no formal complaint has been filed; and offered to either party as appropriate, as reasonably available, and without fee or charge. Examples of supportive measures include, but are not limited to: measures designed to protect the safety of all parties or the District’s educational environment, or deter sexual harassment; counseling; extensions of deadlines or other course-related adjustments; modifications of work or class schedules; campus escort services; mutual restrictions on contact between the parties; changes in work or class locations; leaves of absence; and increased security and monitoring of certain areas of the campus.

  • Structural components means liners, leachate collection systems, final covers, run-on/run-off systems, and any other component used in the construction and operation of the MSWLF that is necessary for protection of human health and the environment.

  • Continuous parameter monitoring system or "CPMS" means all of the equipment necessary to meet the data acquisition and availability requirements of this article, to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and to record average operational parameter value(s) on a continuous basis.

  • Standard Methods for the Examination of Water and Wastewater means the most recent edition of Standard Methods for the Examination of Water and Wastewater published jointly by the American Public Health Association, the American Waterworks Association and the Water Environment Federation;

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Preventive measures means any reasonable measures taken by any person after an incident has occurred to prevent or minimize pollution damage.

  • Components means articles, materials, and supplies incorporated directly into end products at any level of manufacture, fabrication, or assembly by the Contractor or any subcontractor.

  • Pandemic Measures means any quarantine, “shelter in place,” stay at home,” workforce reduction, social distancing, shut down, closure, sequester, immunization requirement, safety or similar Law, directive, guidelines or recommendations promulgated by any Governmental Authority, including the Centers for Disease Control and Prevention and the World Health Organization, in each case, in connection with or in response to a pandemic, including COVID-19.

  • Vehicle measuring attitude means the position of the vehicle as defined by the co-ordinates of fiducial marks in the three-dimensional reference system.

  • Assistive Devices means any category of durable medical equipment, mechanical apparatus, electrical appliance, or instrument of technology used to assist and enhance an individual's independence in performing any activity of daily living. Assistive devices include the use of service animals, general household items, or furniture to assist the individual.

  • Continuous parameter monitoring system (CPMS means all of the equipment necessary to meet the data acquisition and availability requirements of the Prevention of Significant Deterioration program, to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and to record average operational parameter value(s) on a continuous basis.

  • Predictive emissions monitoring system or "PEMS" means all of the equipment necessary to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and calculate and record the mass emissions rate (for example, pounds per hour) on a continuous basis.

  • Biometrics means a technique of personal identification that is based on physical, physiological or behavioural characterisation including blood typing, fingerprinting, DNA analysis, retinal scanning and voice recognition;

  • Measurement means metered volumes at a custody transfer meter through a turbine, Coriolis, or such other meter.

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Structural component means a component that supports non-variable forces or weights (dead loads) and variable forces or weights (live loads).

  • Technology protection measure means a specific technology that blocks or filters Internet access to visual depictions that are:

  • Source of Measure Decree No: 301/PM, Dated: 12 October 2005 of Prime Minister regarding the implementation of the Law on the Promotion of the Foreign Investment, Article 39-43.

  • Energy efficiency measure means equipment, devices, or materials intended to decrease energy consumption, including, but not limited to, upgrades to a building envelope such as insulation and glazing; improvements in heating, ventilating and cooling systems; automated energy control systems; improved lighting, including daylighting; energy‑recovery systems; combined heat and power systems; or another utility cost‑savings measure approved by the governing body.

  • Measurement Point means the emission source for which continuous emission measurement systems (CEMS) are used for emission measurement, or the cross-section of a pipeline system for which the CO2 flow is determined using continuous measurement systems;

  • Beam monitoring system means a system designed and installed in the radiation head to detect and measure the radiation present in the useful beam.

  • Performance Monitoring System has the meaning given to it in paragraph 1.1.2 in Part B of Schedule 6 (Service Levels, Service Credits and Performance Monitoring);

  • Structural pest control means a use requiring a license under Chapter 14 (commencing with Section 8500), Division 3, of the Business and Professions Code.

  • External beam radiation therapy means therapeutic irradiation in which the source of radiation is at a distance from the body.