Maximum tolerance definition

Maximum tolerance means the highest degree of restraint that the military, police and other peace keeping authorities shall observe during a public assembly or in the dispersal of the same.

Examples of Maximum tolerance in a sentence

  • Maximum tolerance in verticality that will be permitted is one mm per 360mm of tower height.

  • Maximum tolerance in verticality that will be permitted is ONE mm per 360mm of tower height.

  • Pitch of distribution pipes or proprietary disposal devices: Maximum tolerance of distribution pipes or proprietary disposal devices must be no more than 2 inches in 100 feet.

  • Random controls are performed and the office responsible for these controls is: Mr. Carlos Pavletic Ministry of Health Mac-Iver 459 Piso 7º SantiagoTel.: (56 2) 2574-0493E-mail: cpavletic@minsal.cl Maximum tolerance levels are set for all approved pesticides.

  • Maximum tolerance of + 10 mm.• Compaction shall show no movement of material under the roller, minimum of 6 passes.• Compaction test standard shall be 95% MDD (AASHTO T99)Measurement Unit: m2The measurement shall be the area of carriageway graded, measured net according to the specified width and measured length graded.

  • Maximum tolerance (mm) in: Grade of FinishLine and LevelAbrupt IrregularityGradual IrregularityDimensionU1+/- 126+/- 6-U2+/- 63+/- 3-U3+/- 63+/- 3-F1+/- 126+/- 6+12, -6F2+/- 66+/- 6+12, -6F3+/- 33+/- 3+/- 6 1.7.13.

  • A Maximum tolerance of 2.5% will be allowed at any point on the dyno curves for both power and torque.

  • DEMONSTRATIONS/MASS ACTIONS• Inform NCDA Management.• Immediately report to PNP.• Maximum tolerance must be observed and maintained at all times.• Ensure that designated open gates must not be blocked by the demonstrators.• Non-obstructive demonstrations should not be interrupted.

  • Random controls are performed and the office responsible for these controls is: Mr. Carlos Pavletic Ministry of Health Mac-Iver 459 Piso 7º SantiagoTel.: (56 2) 574-0440E-mail: cpavletic@minsal.cl Maximum tolerance levels are set for all approved pesticides.

  • Recrystallization of the residue from isopropanol yielded compound M2 as colorless needles (122 mg).

Related to Maximum tolerance

  • Tolerance means a state of adaptation in which exposure to a drug induces changes that result in a diminution of one or more of the drug’s effects over time.

  • Exceedance means a condition that is detected by monitoring that provides data in terms of an emission limitation or standard and that indicates that emissions (or opacity) are greater than the applicable emission limitation or standard (or less than the applicable standard in the case of a percent reduction requirement) consistent with any averaging period specified for averaging the results of the monitoring.

  • Maximum Daily Starts means the maximum number of times that a generating unit can be started in an Operating Day under normal operating conditions.

  • Maximum Daily Limit means the maximum allowable "Daily Concentration" (defined above) when expressed as a concentration (e.g. mg/l), otherwise, it means the maximum allowable "Daily Quantity" as defined above, unless it is expressed as a flow quantity. If expressed as a flow quantity it means "Maximum Daily Flow" as defined in Section 22a-430-3(a) of the RCSA.

  • Maximum Daily Quantity means the daily volume of Gas or Liquids, expressed in 103m3, identified in a Shipper's Interruptible Transportation Service Agreement that Transporter agrees to receive from Shipper under Toll Schedule Interruptible Full Path Service, Toll Schedule Interruptible Receipt Service or Toll Schedule Interruptible Delivery Service, as applicable.

  • Maximum Weekly Starts means the maximum number of times that a generating unit can be started in one week, defined as the 168 hour period starting Monday 0001 hour, under normal operating conditions. Member:

  • Maximum design heat input means the ability of a unit to combust a stated maximum amount of fuel per hour on a steady state basis, as determined by the physical design and physical characteristics of the unit.

  • Normal Maximum Generation means the highest output level of a generating resource under normal operating conditions.

  • Maximum mass means the maximum mass stated by the vehicle manufacturer to be technically permissible (this mass may be higher than the "permissible maximum mass" laid down by the national administration).

  • Maximum means an actual NAV figure of 110% of the Target NAV. In the event Granite elects to declare a special distribution in certain circumstances, the NAV per unit shall be adjusted by any cash component of such special distribution.

  • Maximum allowable residential density means the density allowed under the zoning ordinance and land use element of the general plan, or if a range of density is permitted, means the maximum allowable density for the specific zoning range and land use element of the general plan applicable to the project. Where the density allowed under the zoning ordinance is inconsistent with the density allowed under the land use element of the general plan, the general plan density shall prevail.

  • Maximum Generation Emergency means an Emergency declared by the Office of the Interconnection to address either a generation or transmission emergency in which the Office of the Interconnection anticipates requesting one or more Generation Capacity Resources, or Non- Retail Behind The Meter Generation resources to operate at its maximum net or gross electrical power output, subject to the equipment stress limits for such Generation Capacity Resource or Non-Retail Behind The Meter resource in order to manage, alleviate, or end the Emergency.

  • Maximum Generation Emergency Alert means an alert issued by the Office of the Interconnection to notify PJM Members, Transmission Owners, resource owners and operators, customers, and regulators that a Maximum Generation Emergency may be declared, for any Operating Day in either, as applicable, the Day-ahead Energy Market or the Real-time Energy Market, for all or any part of such Operating Day. Maximum Run Time:

  • Density means mass per unit volume at 15 degrees Celsius expressed in kilograms per cubic metre.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • Total maximum daily load or "TMDL" means the sum of the individual wasteload allocations for point sources, load allocations (LAs) for nonpoint sources, natural background loading and a margin of safety. TMDLs can be expressed in terms of either mass per time, toxicity, or other appropriate measure. The TMDL process provides for point versus nonpoint source trade-offs.

  • Maximum allowable cost means the maximum amount that a pharmacy benefit manager will reimburse a pharmacy for the cost of a drug.

  • Maximum allowable cost list means a list of drugs for

  • Normal Minimum Generation means the lowest output level of a generating resource under normal operating conditions.

  • Maximum Price means an amount (excluding related brokerage, commission, applicable goods and services tax, stamp duties, clearance fees and other related expenses) which may be paid for an ordinary share purchased or acquired by us pursuant to the mandate contained in paragraph (a) above, not exceeding, in the case of a market purchase of an ordinary share, the highest independent bid or the last independent transaction price, whichever is higher, of our ordinary shares quoted or reported on the NASDAQ Global Select Market or the securities exchange operated by JSE Limited (the “JSE”), as the case may be, or shall not exceed any volume weighted average price, or other price determined under any pricing mechanism, in compliance with the requirements under Rule 10b-18 under the Exchange Act, at the time the purchase is effected; and

  • Outputs means the goods or services that are produced by an entity or other person;

  • Maximum Put Amount means, with respect to any Put, the lesser of (a) Five Hundred Thousand Dollars ($500,000), or (b)Five Hundred (500%) percent of the Weighted Average Volume for the twenty (20) Trading Days immediately preceding the Put Date.

  • Maximum Term Loan Amount means Forty Million and No/100 Dollars ($40,000,000).

  • Maximum Legal Rate means the maximum nonusurious interest rate, if any, that at any time or from time to time may be contracted for, taken, reserved, charged or received on the indebtedness evidenced by the Note and as provided for herein or the other Loan Documents, under the laws of such state or states whose laws are held by any court of competent jurisdiction to govern the interest rate provisions of the Loan.

  • Altitude means the vertical distance of a level, a point or an object considered as a point, measured from mean sea level (MSL);

  • Maximum Limit means that number of issued Shares representing 10% of the total number of issued Shares as at the date of the passing of this Resolution (excluding any Shares which are held as treasury shares as at that date); and