Horizontal distance definition

Horizontal distance means the distance between two points measured at a zero percent slope.
Sample 1Sample 2Sample 3
Horizontal distance means the distance between two points measured at a 0% slope.
Sample 1Sample 2Sample 3
Horizontal distance means the distance between two points meas- ured at a zero percent slope.
Sample 1Sample 2

Examples of Horizontal distance in a sentence

  • Horizontal distance between water mains and sewer mains and services shall be a minimum of l0’.

  • Horizontal distance between the test pieces and the infrared camera lens was 600 mm, which gave a spatial resolution of 47 ppi.Image sequences for this method were recorded individually for every lamella specimen and were relatively short compared to those of on-line thermography.

  • The rated capacity of the tank was 50RTh. Horizontal distance between axis of two adjacent tubes was 53mm while vertical distance was 55mm.

  • When the model predicts all the variations in the response data, the coefficient of determination is Table 1.: Regression parameters for standard dimensions overhead transmission line Horizontal distance (m)Desired variable 1.

  • Load Radius: Horizontal distance from a projection of the axisby 50% when the wind speed is 9m/s (20mph) to 12m/s (27mph) ; reduced by 70% when the wind speed is 12m/sof rotation to supporting surface before loading to the center of the vertical hoist line or tackle with load applied.(27mph) to 14m/s (31mph).

  • Horizontal distance to water has been recognized as an important factor in livestock grazing distribution for over 55 years.

  • Horizontal distance between water mains and other utilities, except sewer, shall be a minimum of 5’.

  • Horizontal distance The horizontal distance can be measured by using traditional plumb bob and offset tape or EDM instrument.

  • Horizontal distance between the top and bottom elements of a skewed fraction.

  • Legend:Dimension X - Horizontal distance between hinge axis of the door and the rear axle of the motor.


More Definitions of Horizontal distance

Horizontal distance means the distance between two points measured at a zero percent slope. "Hyporheic" means an area adjacent to and below channels where interstitial water is exchanged with channel water and water movement is mainly in the downstream direction.
Sample 1

Related to Horizontal distance

  • Horizontal well means a well bore drilled laterally at an angle of at least eighty (80) degrees to the vertical or with a horizontal projection exceeding one hundred (100) feet measured from the initial point of penetration into the productive formation through the terminus of the lateral in the same common source of supply.

  • travel distance means the distance an occupant has to travel to reach an exit.

  • Built-up area and/or “Covered Area” in relation to a Flat shall mean the floor area of that Flat including the area of balconies and terraces, if any attached thereto, and also the thickness of the walls (external or internal) and the columns and pillars therein Provided That if any wall, column or pillar be common between two Flats, then one-half of the area under such wall column or pillar shall be included in the built-up area of each such Flat.

  • Taximeter means any device for calculating the fare to be charged in respect of any journey in a hackney carriage or private hire vehicle by reference to the distance travelled or time elapsed since the start of the journey, or a combination of both; and

  • Distance means the great circle distance between the aerodrome of departure and the aerodrome of arrival plus an additional fixed factor of 95 km; and

  • Demarcation Point means the point where Qwest owned or controlled facilities cease, and CLEC, End User Customer, premises owner or landlord ownership or control of facilities begin. "Designed, Verified and Assigned Date" or "DVA" means the date on which implementation groups are to report that all documents and materials have been received and are complete.

  • stratigraphic test well means a drilling effort, geologically directed, to obtain information pertaining to a specific geologic condition. Ordinarily, such wells are drilled without the intention of being completed for hydrocarbon production. They include wells for the purpose of core tests and all types of expendable holes related to hydrocarbon exploration. Stratigraphic test wells are classified as (i) "exploratory type" if not drilled into a proved property; or (ii) "development type", if drilled into a proved property. Development type stratigraphic wells are also referred to as "evaluation wells".

  • at a distance means that the service is provided without the parties being simultaneously present;

  • Motor-driven cycle means every motorcycle that has a gasoline engine that (i) displaces less than

  • Basal area means the effective surface area available to transmit the treated effluent from the filter media in a mound system into the in-situ receiving soils. The perimeter is measured at the interface of the imported fill material and in-situ soil. On sloping sites, only the area down-gradient from the up-slope edge of the distribution media may be included in this calculation.

  • Diameter means the diameter of the stem of a tree measured outside the bark at a specified point of measurement.

  • Modular building means, but shall not be limited to, single and multifamily houses, apartment

  • Water surface elevation means the height, in relation to the National Geodetic Vertical Datum (NGVD) of 1929, the North American Vertical Datum (NAVD) of 1988, or other datum, where specified, of floods of various magnitudes and frequencies in the floodplains of riverine areas.

  • service well means a well drilled or completed for the purpose of supporting production in an existing field. Wells in this class are drilled for the following specific purposes: gas injection (natural gas, propane, butane or flue gas), water injection, steam injection, air injection, salt water disposal, water supply for injection, observation or injection for combustion.

  • Unstable area means a location that is susceptible to natural or human-induced events or forces capable of impairing the integrity of some or all of the landfill structural components responsible for preventing releases from a landfill. Unstable areas can include poor foundation conditions, areas susceptible to mass movements, and Karst terranes.

  • Acre-foot means the amount of water necessary to cover one acre of land to the depth of one foot, or 325,851 U.S. gallons of water.

  • Perimeter means the fenced or walled area of the institution that restrains the movement of the inmates.

  • Water Meter means any apparatus for measuring or showing the volume of water supplied to, or of effluent discharged from any premises;

  • Urban growth areas means those areas designated by a county pursuant to RCW 36.70A.110.

  • Landing area means that part of a movement area intended for the landing or take-off of aircraft;

  • Substation means the apparatus that connects the electrical collection system of the WECS(s) and increases the voltage for connection with the utility's transmission lines.

  • Coastal area means coastal area as defined in section 22a-93(3) of the Connecticut General Statutes. “Coastal waters” means coastal waters as defined in section 22a-93(5) of the Connecticut General Statutes. “Commissioner” means commissioner as defined in section 22a-2(b) of the Connecticut General Statutes.

  • Modular building retailer means any person who purchases or acquires a modular building from a