Common use of Waistband Clause in Contracts

Waistband. The trouser will be made with the Freedom Fit® waistband system, which is designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be constructed using the "closed method" and shall measure a minimum of 1-7/8" wide when finished. The waistband closure shall be accomplished with a single crush proof hook and eye centered on the waistband for maximum wearer comfort. The hook and eye shall be reinforced with 7/8-inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband (bartacks in place of topstitching shall be cause for rejection). In addition to the stitching of the waistband when it is set onto the trouser, the waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser to be finished to allow for alterations (with ample basic trouser fabric and waistband curtain material to allow trouser size to be increased at least one size). The outlet in the seat is to be in proportion to waist outlet so seat may also be let out. Seat seam must be sewn with a tandem needle machine (double-needle stitch) for maximum strength. The waistband curtain is composed of two elastic components, which give it two-zone comfort fit and breathability. The top part of the waistband curtain is interlined with a 1-1/2” elastic band that has two functions. It stabilizes the waistband, preventing waistband rollover, and allows for a comfort stretch when the wearer bends or sits. This elastic is around the entire waistband and is constructed with an open weave to allow for breathability. The specification for the upper elastic is as follows: Width 1 ½” Overall content: 38% Polyester, 45% Nylon, 17% Spandex Stretch: 20% The upper part or the waistband curtain interlining (elastic band) is to be lined in black (the same color as the pocketing material) and it shall be cut on a 45-degree bias to allow for maximum stretch. The waistband basic trouser fabric shall be cut across the cloth to allow for maximum stretch in synergy with the Freedom Fit Waistband. The lower part of the waistband shall also be black and is designed to stretch over the hips for comfort and helps keep the trouser positioned properly on the waist. This elastic is also woven with an open weave for maximum breathability. The lower elastic portion of the band has an area of exposed black Neoprene rubber, which acts as a shirt keeper. The specifications for the lower elastic are as follows: Width: 1 ¾” Overall Content: 13% Polyester, 49% Nylon, 16% Spandex, 22% Rubber Stretch: 55% The three (3) black rubberized strands match the waistband curtain and are designed to keep shirts tucked in for neat appearance (use of silicone strip or strips instead of rubberized strands shall be cause for rejection). The waistband to be constructed using the "Xxxxxx method" and measure 2" wide when finished. The waistband curtain to be made of black starspun and must be attached to the trouser with a Xxxxx Machine. The waistband must contain ¾" wide BAN-ROL to prevent roll over and have Snugtex to keep shirts tucked in. The waistband closure to be accomplished with a crush-proof hook and eye. The hook and eye to be reinforced with stays made of non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. There is to be topstitching 1/16" below the waistband seam for added strength.

Waistband. The trouser Covert waistband contains a hidden elastic extension, providing up to three inches of additional stretch. The front of the outer waistband tapers through the covert opening at the top of the front pocket opening. The 1¼” wide elastic extends from the end of the taper through the waistband behind the side seam. All stress points will be bartacked. The inner waistband shall be a Duty Fit waistband, which provides additional stretch to the wearer’s exact size while providing permanent recovery memory. The Duty Fit waistband will be continuous on the inside of the waistband so as to provide additional support and recovery to the waistband extension. There are no split openings in the inside curtain. The inside waistband shall be made with black poly/spandex/nylon/latex with 50% stretch. There is a ½” exposed gripper track in the Freedom Fit® waistband system, which is designed to provide the wearer with a more comfortable and better fitting trousercenter for shirt retention. The waistband measures 2½” and is attached with a xxxxx machine. Knit elastic banrol stiffener measuring 1” shall be sewn into the entire waistband to provide additional support. The waistband is to be constructed using the "closed method" method and shall measure a minimum of 1-7/82" wide when finished. The waistband closure shall be accomplished with a single double crush proof hook and eye centered on the waistband eye, bartacked for maximum wearer comfortstability. The hook hooks and eye eyes shall be reinforced with 7/8-inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband (bartacks in place of topstitching shall be cause for rejection). In addition to the stitching of the waistband when it is set onto the trouser, the waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser to be finished to allow for alterations (with ample basic trouser fabric and waistband curtain material to allow trouser size to be increased at least one size). The outlet in the seat is to be in proportion to waist outlet so seat may also be let out. Seat seam must be sewn with a tandem needle machine (double-needle stitch) for maximum strength. The waistband curtain is composed of two elastic components, which give it two-zone comfort fit and breathability. The top part of the waistband curtain is interlined with a 1-1/2” elastic band that has two functions. It stabilizes the waistband, preventing waistband rollover, and allows for a comfort stretch when the wearer bends or sits. This elastic is around the entire waistband and is constructed with an open weave to allow for breathability. The specification for the upper elastic is as follows: Width 1 ½” Overall content: 38% Polyester, 45% Nylon, 17% Spandex Stretch: 20% The upper part or the waistband curtain interlining (elastic band) is to be lined in black (the same color as the pocketing material) and it shall be cut on a 45-degree bias to allow for maximum stretch. The waistband basic trouser fabric shall be cut across the cloth to allow for maximum stretch in synergy with the Freedom Fit Waistband. The lower part of the waistband shall also be black and is designed to stretch over the hips for comfort and helps keep the trouser positioned properly on the waist. This elastic is also woven with an open weave for maximum breathability. The lower elastic portion of the band has an area of exposed black Neoprene rubber, which acts as a shirt keeper. The specifications for the lower elastic are as follows: Width: 1 ¾” Overall Content: 13% Polyester, 49% Nylon, 16% Spandex, 22% Rubber Stretch: 55% The three (3) black rubberized strands match the waistband curtain and are designed to keep shirts tucked in for neat appearance (use of silicone strip or strips instead of rubberized strands shall be cause for rejection). The waistband to be constructed using the "Xxxxxx method" and measure 2" wide when finished. The waistband curtain to be made of black starspun and must be attached to the trouser with a Xxxxx Machine. The waistband must contain ¾" wide BAN-ROL to prevent roll over and have Snugtex to keep shirts tucked in. The waistband closure to be accomplished with a crush-proof hook and eye. The hook and eye to be reinforced with stays made of a non-woven fabric that are anchored by the topstitching top-stitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must have a crack stitch for added strength. No alternative waistband will be acceptable. Inner Fly/Crotch: The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a non-woven interlining sewn to the fly to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the join seam across the inseam and end 1" onto the backseam. A separate french fly made of the outer fabric shall be sewn to the inside right fly. There shall be a triple strength crotch reinforcement to prevent seam failure in the crotch and inseam area. The crotch shall be secured with two rows of stitching. One row is to be topstitching 1/16" on the inside of the trouser, then turned and an additional row to be sewn on the outside of trouser. Zipper: The trousers shall be closed with a gun metal memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bartack located below the bottom zipper stop on the inside of the trouser. Belt Loops: There should be a minimum of 5 lined loops on waist sizes 30 and below, 7 lined loops on waist sizes 31 through 48, and 9 lined loops on waist sizes 50 and over. Each loop is to be ⅞" wide of double thickness, with stitching on the face side ⅜" from each edge. Except for the back loop which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the xxxxx. They shall accommodate a 1⅝" belt. Striping: O fficer’s trousers to have X.X. Xxxx ¼” silver braid on each side seam for added strengthto waistband.

Waistband. The trouser will be made with the Freedom Fit® waistband system, which is designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be the Duty Fit waistband, which provides an exact fit by stretching to the wearer’s exact size. The inside waistband shall be made with charcoal wrapped woven elastine and have two tracks of 1/8” wide silicone for shirt retention. It measures 2½” and is attached with a xxxxx machine. Woven elastic banrol stiffener measuring 1” shall be sewn into the entire waistband to provide additional support. The waistband is to be constructed using the "closed method" method and shall measure a minimum of 1-7/82" wide when finished. The waistband closure shall be accomplished with a single double crush proof hook and eye centered on the waistband eye, bartacked for maximum wearer comfortstability. The hook hooks and eye eyes shall be reinforced with 7/8-inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband (bartacks in place of topstitching shall be cause for rejection). In addition to the stitching of the waistband when it is set onto the trouser, the waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser to be finished to allow for alterations (with ample basic trouser fabric and waistband curtain material to allow trouser size to be increased at least one size). The outlet in the seat is to be in proportion to waist outlet so seat may also be let out. Seat seam must be sewn with a tandem needle machine (double-needle stitch) for maximum strength. The waistband curtain is composed of two elastic components, which give it two-zone comfort fit and breathability. The top part of the waistband curtain is interlined with a 1-1/2” elastic band that has two functions. It stabilizes the waistband, preventing waistband rollover, and allows for a comfort stretch when the wearer bends or sits. This elastic is around the entire waistband and is constructed with an open weave to allow for breathability. The specification for the upper elastic is as follows: Width 1 ½” Overall content: 38% Polyester, 45% Nylon, 17% Spandex Stretch: 20% The upper part or the waistband curtain interlining (elastic band) is to be lined in black (the same color as the pocketing material) and it shall be cut on a 45-degree bias to allow for maximum stretch. The waistband basic trouser fabric shall be cut across the cloth to allow for maximum stretch in synergy with the Freedom Fit Waistband. The lower part of the waistband shall also be black and is designed to stretch over the hips for comfort and helps keep the trouser positioned properly on the waist. This elastic is also woven with an open weave for maximum breathability. The lower elastic portion of the band has an area of exposed black Neoprene rubber, which acts as a shirt keeper. The specifications for the lower elastic are as follows: Width: 1 ¾” Overall Content: 13% Polyester, 49% Nylon, 16% Spandex, 22% Rubber Stretch: 55% The three (3) black rubberized strands match the waistband curtain and are designed to keep shirts tucked in for neat appearance (use of silicone strip or strips instead of rubberized strands shall be cause for rejection). The waistband to be constructed using the "Xxxxxx method" and measure 2" wide when finished. The waistband curtain to be made of black starspun and must be attached to the trouser with a Xxxxx Machine. The waistband must contain ¾" wide BAN-ROL to prevent roll over and have Snugtex to keep shirts tucked in. The waistband closure to be accomplished with a crush-proof hook and eye. The hook and eye to be reinforced with stays made of non-woven a nonwoven fabric that are anchored areanchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must have a crack stitch for added strength. No alternative waistband will be acceptable. Inner Fly/Crotch: The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a nonwoven interlining sewn to the fly to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper andcontinuecentered on the join seam across the inseam and end 1" onto the backseam. A separate french fly made of the outer fabric shall be sewn to the inside right fly. There shall be a triple strength crotch reinforcement to prevent seam failure in the crotch and inseam area. The crotch shall be secured with two rows of stitching. One row is to be topstitching 1/16" on the inside of the trouser, then turned and an additional row to be sewn on the outside of trouser. Zipper: The trousers shall be closed with a brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bartack located below the bottom zipper stop on the inside of the trouser. Belt Loops: There should be a minimum of 5 lined belt loops on waist sizes 28, 29, 30, and a minimum of 7 lined loops on all sizes over 30. Each loop is to be ⅞" wide of double thickness, withstitching on the face side ⅜" from each edge. Except for the back loop which shall be tacked on, all loops shall be sewn into the bottom of the waistband seam for added strengthand into the xxxxx. Belt loops shall accommodate a 1⅝" belt.