Total Moisture Sample Clauses

Total Moisture. Sample for determination of Total Moisture shall be segregated from the sample collected at the Delivery Point jointly by the Seller and the Purchaser, and prepared and analysed, as per procedure given in Schedule-V
View SourceView Similar (9)
Total Moisture. Sample fordetermination ofTotal Moistureshall besegregated fromthe samplecollected at the Delivery Point jointly by the Seller and the Purchaser, and prepared and analysed, as per procedure given in Schedule-IV
View SourceView Similar (2)
Total Moisture. Sample for determination of Total Moisture shall be segregated from the sample collected at the Delivery Point by the Third Party, and prepared and analyzed, as per procedure given in Schedule-V.
View SourceView Similar (2)
Total Moisture. (a) If the total moisture percentage of a shipment of Coal as determined by the Inspection Company is in the range of 10% and 13% inclusive, then adjustment of total weight for invoice and price of that shipment of Coal pursuant to Section 8.1 shall be made as follows: (i) If the total moisture of a shipment of Coal exceeds 10 %, the exceeded percentages shall be applied to and deducted from the total weight of Coal for calculation of the total invoice amount. (ii) If the total moisture of a shipment of Coal exceeds 11.5 %, the price of that shipment of Coal pursuant to Section 8.1 (i) shall be further reduced by the following amount to compensate for additional ocean freight payable by the Buyer for that shipment of Coal by reason of such excessive moisture content: Ocean Freight Quantity per M - 11.5 % Rate per Ton X Section 6.1 X - - - - - - - - 100 % - 11.5 % Where "M" represents the actual total moisture percentage of that shipment of Coal as determined by the Inspection Company. The deduction and charge in (i) and (ii) above shall be cumulative. (b) The Buyer shall have the right to reject any shipment of Coal if, based on the Inspection Company's determination, the total moisture exceeds 13 %. If Buyer determines not to reject such shipment of Coal, a further price reduction for such shipment shall be made as mutually agreed by the Parties.
View Source

Related to Total Moisture

  • Temperature Measurement Temperature will be measured by the nearest automatic Melbourne Bureau of Meteorology Monitoring Station for example (but not limited to): Melbourne, Moorabbin, Dunns Hill, Melbourne Airport, Frankston, and Point ▇▇▇▇▇▇. At the commencement of each project, the onsite management and employee representatives shall agree which is to be the applicable automatic weather monitoring station.

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Quality control system (i) The Contractor shall establish a quality control mechanism to ensure compliance with the provisions of this Agreement (the “Quality Assurance Plan” or “QAP”). (ii) The Contractor shall, within 30 (thirty) days of the Appointed Date, submit to the Authority’s Engineer its Quality Assurance Plan which shall include the following: (a) organisation, duties and responsibilities, procedures, inspections and documentation; (b) quality control mechanism including sampling and testing of Materials, test frequencies, standards, acceptance criteria, testing facilities, reporting, recording and interpretation of test results, approvals, check list for site activities, and proforma for testing and calibration in accordance with the Specifications for Road and Bridge Works issued by MORTH, relevant IRC specifications and Good Industry Practice; and (c) internal quality audit system. The Authority’s Engineer shall convey its approval to the Contractor within a period of 21 (twenty-one) days of receipt of the QAP stating the modifications, if any, required, and the Contractor shall incorporate those in the QAP to the extent required for conforming with the provisions of this Clause 11.2. (iii) The Contractor shall procure all documents, apparatus and instruments, fuel, consumables, water, electricity, labour, Materials, samples, and qualified personnel as are necessary for examining and testing the Project Assets and workmanship in accordance with the Quality Assurance Plan. (iv) The cost of testing of Construction, Materials and workmanship under this Article 11 shall be borne by the Contractor.

  • Maximum Total Leverage Ratio The Borrower shall not permit the Total Leverage Ratio as of the last day of any four-quarter period to be greater than 4.00:1.00. Notwithstanding the foregoing: (a) for purposes of calculating the Total Leverage Ratio, until the earlier of (i) the consummation of a Specified Acquisition and (ii) termination of the acquisition agreement related to such Specified Acquisition, the Total Leverage Ratio shall not include any Indebtedness of the Borrower or the Guarantors to the extent that (x) such Indebtedness was incurred solely to finance such Specified Acquisition (and any related transactions) and the proceeds of such indebtedness are held as cash or cash equivalents in an escrow or equivalent arrangement (pending the consummation of such Specified Acquisition) and (y) such Indebtedness is redeemable or prepayable at no more than 101% of the principal amount thereof (plus accrued interest) in the event that the Specified Acquisition is not consummated; and (b) upon the Administrative Agent’s receipt of a written notice substantially in the form of Exhibit F hereto (a “Specified Acquisition Notice”), the Total Leverage Ratio as of the last day of any period for the four-quarter period beginning with the period in which such Specified Acquisition is consummated (such period in which the Specified Acquisition is consummated, the “Specified Acquisition Consummation Period”) and continuing through the fourth consecutive fiscal quarter ended immediately following the first day of the Specified Acquisition Consummation Period shall not exceed 4.50:1.00 (in lieu of the ratio set forth for such period above); provided that (i) the Borrower may deliver a Specified Acquisition Notice no more than three times during the life of this Agreement and (ii) after any Specified Acquisition Consummation Period, the Borrower must have a Total Leverage Ratio of no more than 4.00:1.00 for at least two consecutive fiscal quarters before the Borrower may elect to deliver a Specified Acquisition Notice for an additional time.

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.