Common use of Process Certification Clause in Contracts

Process Certification. 63.1 Company has the right, subject to the terms of Article 29, to review, inspect, and evaluate Supplier’s Material and supplies, Supplier’s facilities at which Supplier manufactures Products for Company under this Agreement, including Material management systems and supply line management processes and procedures and Supplier’s sources for Material and supplies to the extent related to Supplier’s performance of its obligations under this Agreement. Company has the right to specify the types of Material used in the manufacture and/or repair of the Product and/or suppliers of Material at any time during the Term of this Agreement. If such selection of Material impacts the previously agreed to Product prices, such subsequent Product prices shall be negotiated in good faith and mutually agreed to by the parties. All changes to Material, supplies, sites of manufacture and repair, and vendors must be approved in writing by Company. In regard to Supplier’s manufacturing and repair process for the Products, Company reserves the right, subject to the terms of Article 30, to perform periodic quality audits, surveys, evaluations, and approvals, including, but not limited to, analysis of each manufacturing, assembly, and/or test position for acceptability of procedures, equipment calibration, test software including change control, and operator performance, as well as evaluation of quality control/quality assurance and data collection and analysis procedures, to the extent related to Supplier’s performance of its obligations under this Agreement. 63.2 Supplier shall conduct appropriate incoming inspection of Material used in the manufacture of Products in accordance with its standard practices and shall maintain a Supplier control, approval, and corrective action process. Such standard practices shall be subject to audit and approval by Company and Company may require Supplier to implement recommended changes in order to facilitate Supplier’s manufacture of conforming Product. Such practices may be modified from time to time to address specific conditions as requested by Company. 63.3 Subject to compliance with Article 29, Supplier agrees to provide Company reasonable access, so as not to interrupt Supplier’s production processes, to applicable test equipment at Supplier’s facilities at which Products are manufactured under this Agreement in order for Company to (a) do test program development or (b) do final prove-in or acceptance of any test programs.

Process Certification. 63.1 56.1 Company has the right, subject to the terms of Article 2930, to review, inspect, and evaluate Supplier’s Material and supplies, Supplier’s facilities at which Supplier manufactures Products for or Company under this Agreement, including Material management systems and supply line management processes and procedures and Supplier’s sources for Material and supplies to the extent related to Supplier’s performance of its obligations under this Agreement. Subject to the terms of Article 30, Company may request that Supplier extend the foregoing right to any customer of Company designated by it, or any designated customer of such a Company customer, provided that any such extension shall be at Supplier’s discretion, acting reasonably. Company has the right to specify the types of Material used in the manufacture and/or repair of the Product and/or suppliers of Material at any time during the Term of this Agreement. If such selection of Material impacts the previously agreed to Product prices, such subsequent Product prices shall be negotiated in good faith and mutually agreed to by the partiesParties. All changes to Material, supplies, sites of manufacture and repair, and vendors must be approved in writing by Company. In regard to Supplier’s manufacturing and repair process for the Products, Company reserves the right, subject to the terms of Article 30, to perform periodic quality audits, surveys, evaluations, and approvals, including, but not limited to, analysis of each manufacturing, assembly, and/or test position for acceptability of procedures, equipment calibration, test software including change control, and operator performance, as well as evaluation of quality control/quality assurance and data collection and analysis procedures, to the extent related to Supplier’s performance of its obligations under this Agreement. 63.2 56.2 Supplier shall conduct appropriate incoming inspection of Material used in the manufacture and repair of Products in accordance with its standard practices Company specifications and shall maintain a Supplier supplier control, approval, and corrective action process. Such standard practices shall be subject to audit and approval by Company and Company may require Supplier to implement recommended changes in order to facilitate Supplier’s manufacture of conforming Product. Such practices may be modified from time to time to address specific conditions as requested by Company. 63.3 56.3 Subject to compliance with Article 2930, Supplier agrees to provide Company reasonable access, so as not to interrupt Supplier’s production processes, to applicable test equipment at Supplier’s facilities at which Products are manufactured under this Agreement in order for Company to (a) do test program development or (b) do final prove-in or acceptance of any test programs.