Common use of Overturning Clause in Contracts

Overturning. 8.1.2.1. The manikin shall be equipped with the load application device as described in Annex 23 and placed in the restraints installed in accordance with this Regulation and taking into account the manufacturer's instructions and with the standard slack as specified in paragraph 8.1.3.6. below, applied for all systems identically. 8.1.2.2. The restraint shall be fastened to the test seat or vehicle seat. The whole seat shall be rotated around a horizontal axis, contained in the median longitudinal plane of the seat through an angle of 540° +/- 5° at a speed of 2-5 degrees/second and stopped in this position. For the purposes of this test, devices intended for use in specific cars may be attached to the test seat described in Annex 6. 8.1.2.3. At this static inverted position a mass equivalent to 4 times that of the dummy shall be applied vertically downwards in a plane perpendicular to the axis of rotation in addition to the dummy utilizing the load application device described in Annex 23. The load shall be applied in a gradual controlled manner at a rate not exceeding gravitational acceleration or 400 mm/min. Maintain the prescribed maximum load for a duration of 30 -0/+5 seconds. 8.1.2.4. Remove the load at a rate not exceeding 400 mm/min and measure displacement. 8.1.2.5. Rotate the whole seat for 180° to return to the starting position. 8.1.2.6. This test cycle shall be carried out again rotating in the reverse direction. With the rotational axis in the horizontal plane and at 90° to that of the two earlier tests, the procedure shall be repeated in the two directions of rotation. 8.1.2.7. These tests shall be carried out using both the smallest and the largest appropriate manikin of the group or groups for which the restraining device is intended. Any adjustment of the dummy or child restraint systems during the complete test cycle is not allowed.

Overturning. 8.1.2.17.1.2.1. The manikin shall be equipped with either of the load application device devices as appropriate, and described in Annex 23 and placed 21. Place the manikin in the restraints installed in accordance with this Regulation and taking into account the manufacturer's instructions and with the standard slack as specified in paragraph 8.1.3.67.1.3.5. below, applied for all systems identically.. Deleted: CRS‐60‐01e.docx2¶ Formatted: English (U.K.) Formatted: English (U.K.) 8.1.2.27.1.2.2. The restraint shall be fastened to the test seat bench or vehicle seat. The whole seat Enhanced child restraint system shall be rotated around a horizontal axis, axis contained in the median longitudinal plane of the seat Enhanced child restraint system through an angle of 540° +/- ± 5° at a speed of 2-5 degrees/second and stopped in this position. For the purposes of this test, devices intended for use in specific cars may be attached to the test seat bench described in Annex 6. 8.1.2.37.1.2.3. At this static inverted position position, a mass equivalent to 4 four times that of the dummy dummy, with a tolerance of -0/+5 per cent with reference to dummies nominal masses as in Annex 8, shall be applied vertically downwards in a plane perpendicular to the axis of rotation in addition to the dummy utilizing the load application device described in Annex 2321. The load shall be applied in a gradual controlled manner at a rate not exceeding gravitational acceleration or 400 mm/min. Maintain the prescribed maximum load for a duration of 30 -0/+5 - 0/+5 seconds. 8.1.2.47.1.2.4. Remove the load at a rate not exceeding 400 mm/min and measure residual displacement. 8.1.2.57.1.2.5. Rotate the whole seat for 180° to return to the starting position. 8.1.2.67.1.2.6. This test cycle shall be carried out again rotating in the reverse direction. With the rotational axis in the horizontal plane and at 90° to that of the two earlier tests, the procedure shall be repeated in the two directions of rotation. 8.1.2.77.1.2.7. These tests shall be carried out using both the smallest and the largest appropriate manikin dummy of the group or groups size range for which the restraining device is intended. Any adjustment of the dummy or Enhanced child restraint systems during the complete test cycle is not allowed.