Tools and Equipment As established by current practices, the Employer may determine and provide necessary tools, tool allowance, equipment and foul weather gear. The Employer will repair or replace employer-provided tools and equipment if damaged or worn out beyond usefulness in the normal course of business. Employees are accountable for equipment and/or tools assigned to them and will maintain them in a clean and serviceable condition.
UNIFORMS, TOOLS AND EQUIPMENT 23.1 Uniforms The Employer may require employees to wear uniforms. Where required, the Employer will determine and provide the uniform or an equivalent clothing allowance. The Employer will follow their policy regarding the provision and maintenance of required uniforms, specialized clothing and footwear. The cost of normal wear and tear and loss of required uniforms, specialized clothing and footwear due to workplace conditions is the responsibility of the Employer.
TOOLS AND CLOTHING 30.1 An employee shall be required to provide himself with the ordinary hand tools of his trade, based on established trade union practices at the time of signing of this Agreement. EPSCA and the Union shall establish an appropriate tool list for each trade. Each Employer will provide, insofar as is practical, separate facilities for storing the tools of each trade, but shall not be held responsible for losses, except as noted hereunder:
Evaluation Software If the Software is an evaluation version or is provided to You for evaluation purposes, then, unless otherwise approved in writing by an authorized representative of Licensor, Your license to use the Software is limited solely for internal evaluation purposes in non-production use and in accordance with the terms of the evaluation offering under which You received the Software, and expires 90 days from installation (or such other period as may be indicated within the Software). Upon expiration of the evaluation period, You must discontinue use of the Software, return to an original state any actions performed by the Software, and delete the Software entirely from Your system and You may not download the Software again unless approved in writing by an authorized representative of Licensor. The Software may contain an automatic disabling mechanism that prevents its use after a certain period of time. RESTRICTIONS
PERSONAL PROTECTIVE EQUIPMENT, TOOLS AND APPAREL 16.01 The Employer will furnish employees with all necessary personal protective equipment (including safety helmets, safety glasses, gloves etc.) and rain gear if and when required. Said equipment shall remain the property of the Employer. Any worn out safety equipment will be replaced by the Employer upon presentation of the worn equipment. The employees shall be held responsible for loss or improper maintenance of Employer furnished items, including personal protective equipment, rain gear and safety equipment, in which case employees may, at the discretion of the Employer, be subject to disciplinary action.
PATROL VIDEO SYSTEMS 2 1. As part of the law enforcement services to be provided to CITY, COUNTY 3 has provided, or will provide, patrol video systems (hereinafter called “PVS”) 4 that are or will be mounted in patrol vehicles designated by COUNTY for 5 use within CITY service area.
For Information/Tools and Other Research Studies Outcome of project. Published documents, including date, title, and periodical name. A discussion of policy development. State if the project has been cited in government policy publications or technical journals, or has been used to inform regulatory bodies. The number of website downloads. An estimate of how the project information has affected energy use and cost, or have resulted in other non-energy benefits. An estimate of energy and non-energy benefits. Data on potential job creation, market potential, economic development, and increased state revenue as a result of project. A discussion of project product downloads from websites, and publications in technical journals. A comparison of project expectations and performance. Discuss whether the goals and objectives of the Agreement have been met and what improvements are needed, if any. • Respond to CAM questions regarding responses to the questionnaires. The Energy Commission may send the Recipient similar questionnaires after the Agreement term ends. Responses to these questionnaires will be voluntary. Products: • Kick-off Meeting Benefits Questionnaire • Mid-term Benefits Questionnaire • Final Meeting Benefits Questionnaire
LOST, STOLEN OR DAMAGED CARDS If the Cardmember loses the Card or if the Card is damaged or stolen or if the PIN became available to any other persons, the Cardmember must immediately inform AEME by telephone. In addition, the Cardmember shall provide AEME with a written notification within 3 days from the date of the occurrence of any of the above listed events, as per applicable laws. All notices pursuant to this article must be sent to the following address: AMEX (Middle East) B.S.C. (c), P.O. Box 5990, Manama, Kingdom of Bahrain. Or facsimile number: (+000) 00 000000. To inform AEME by phone, call the number indicated in the Cardmember Additional Information Leaflet. If AEME is duly informed in the manner described above the Cardmember shall not be liable for any Charges made on his or her Card by any third parties after the Card has been reported lost or stolen. Failure to comply with the provisions of this article will render the Cardmember liable for all Transactions made on his or her lost or stolen Card until the time the Card is reported as lost or stolen to AEME. However, the Cardmember shall at all times be fully liable for all Charges including Cash Withdrawals even if these Charges were made by third parties if these third parties gained possession of the Card or any Supplementary Card or the PIN with the knowledge, permission, approval or other acts of the Cardmember or any Supplementary Cardmember or because of their negligence. If the Card is found after it was reported lost or stolen, the Cardmember may not use or attempt to use the Card at issue and shall immediately inform AEME which will take the appropriate action.
Packet Switching Capability 4.5.1 The packet switching capability network element is defined as the function of routing or forwarding packets, frames, cells or other data units based on address or other routing information contained in the packets, frames, cells or other data units.
USE OF RECYCLED OR REMANUFACTURED MATERIALS New York State supports and encourages contractors to use recycled, remanufactured or recovered materials in the manufacture of products and packaging to the maximum extent practicable without jeopardizing the performance or intended end use of the product or packaging unless such use is precluded due to health or safety requirements or product specifications contained herein. Refurbished or remanufactured components or products are required to be restored to original performance and regulatory standards and functions and are required to meet all other requirements of this bid solicitation. Warranties on refurbished or remanufactured components or products must be identical to the manufacturer's new equipment warranty or industry's normal warranty when remanufacturer does not offer new equipment. See "Remanufactured, Recycled, Recyclable or Recovered Materials" in Appendix B, OGS General Specifications.
