Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
ATM Card If approved, you may use your card and personal identification number (PIN) in automated teller machines (ATMs) of the Credit Union, Instant Cash, and Cirrus® networks, and such other machines or facilities as the Credit Union may designate. For ATM transactions, you must consent to the Credit Union’s overdraft protection plan in order for the transaction amount to be covered under the plan. Without your consent, the Credit Union may not authorize and pay an overdraft resulting from these types of transactions. Services and fees for ATM overdrafts are shown in the document the Credit Union uses to capture the member’s opt-in choice for overdraft protection and the Schedule of Fees and Charges. At the present time, you may use your card to: - Make deposits to your savings and checking accounts. - Withdraw funds from your savings and checking accounts. - Transfer funds from your savings and checking accounts. - Obtain balance information for your savings and checking accounts. - Make point-of-sale (POS) transactions with your card and personal identification number (PIN) to purchase goods or services at POS terminals that carry Instant Cash, and Cirrus® network logo(s). - Access your Overdraft Protection account. The following limitations on ATM Card transactions may apply: - There is no limit on the number of cash withdrawals you may make in any one (1) day. - You may withdraw up to a maximum of $500.00 in any one (1) day, if there are sufficient funds in your account. - There is no limit on the number of POS transactions you may make in any one (1) day. - For security purposes, there are other limits on the frequency and amount of transfers available at ATMs. - You may transfer up to the available balance in your accounts at the time of the transfer. - See Section 2 for transfer limitations that may apply to these transactions. Because of the servicing schedule and processing time required in ATM operations, there may be a delay between the time a deposit (either cash or check) is made and when it will be available for withdrawal.
Statewide HUB Program Statewide Procurement Division Note: In order for State agencies and institutions of higher education (universities) to be credited for utilizing this business as a HUB, they must award payment under the Certificate/VID Number identified above. Agencies, universities and prime contractors are encouraged to verify the company’s HUB certification prior to issuing a notice of award by accessing the Internet (xxxxx://xxxxx.xxx.xxxxx.xx.xx/tpasscmblsearch/index.jsp) or by contacting the HUB Program at 000-000-0000 or toll-free in Texas at 0-000-000-0000.
Television Equipment Recycling Program If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.
STATEWIDE CONTRACT MANAGEMENT SYSTEM If the maximum amount payable to Contractor under this Contract is $100,000 or greater, either on the Effective Date or at any time thereafter, this section shall apply. Contractor agrees to be governed by and comply with the provisions of §§00-000-000, 00-000-000, 00-000-000, and 00- 000-000, C.R.S. regarding the monitoring of vendor performance and the reporting of contract information in the State’s contract management system (“Contract Management System” or “CMS”). Contractor’s performance shall be subject to evaluation and review in accordance with the terms and conditions of this Contract, Colorado statutes governing CMS, and State Fiscal Rules and State Controller policies.
Purchase Order Flip via Ariba Network (AN) The online process allows suppliers to submit invoices via the AN for catalog and non- catalog goods and services. Contractors have the ability to create an invoice directly from their Inbox in their AN account by simply “flipping” the purchase order into an invoice. This option does not require any special software or technical capabilities. For the purposes of this section, the Contractor warrants and represents that it is authorized and empowered to and hereby grants the State and the third-party provider of MFMP the right and license to use, reproduce, transmit, distribute, and publicly display within the system the information outlined above. In addition, the Contractor warrants and represents that it is authorized and empowered to and hereby grants the State and the third-party provider the right and license to reproduce and display within the system the Contractor’s trademarks, system marks, logos, trade dress, or other branding designation that identifies the products made available by the Contractor under the Contract.
Business Auto (i) Coverage shall be at least as broad as the Insurance Services Office Business Auto Coverage form covering Automobile Liability, code 1 “any auto”.
Leave Donation Program Employees may donate paid leave to a fellow employee who is otherwise eligible to accrue and use sick leave and is employed by the same Agency. The intent of the leave donation program is to allow employees to voluntarily provide assistance to their co-workers who are in critical need of leave due to the serious illness or injury of the employee or a member of the employee’s immediate family. The definition of immediate family as provided in rule 123:1-47-01 of the Administrative Code shall apply for the leave donation program.
Local Switching Interfaces 4.2.13.1 Deland Actel shall order ports and associated interfaces compatible with the services it wishes to provide as listed in Exhibit A. BellSouth shall provide the following local switching interfaces:
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where EveryCall has requested an Unbundled Loop and BellSouth uses Integrated Digital Loop Carrier (IDLC) systems to provide the local service to the end user and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to EveryCall. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for EveryCall (e.g. hairpinning):
