Connect the DST Sample Clauses

Connect the DST i and the vehicle side diagnosis connector with the datalink cable. Connected to vehicle side diagnosis connector Notch (Center) Tighten with screws. T01904E CAUTION Do not use a datalink cable other than the dedicated datalink cable supplied with the DST-i. Inspect the cable before connecting for adhesion of foreign materials or damage to the connector pins. When connecting cables, take care to connect them gently and at the proper angle and orientation. If the connection is attempted with the cable upside down or at an angle, there is a risk of damaging the connector terminal and causing malfunctions of the vehicle and/or the DST-i. Do not apply a load to the connector connected with the DST-i. Applying too much force could result in breakage of the connector terminal and it could cause malfunctions or failure of the vehicle and/or the DST-i. NOTE Confirm that the vehicle ignition or key switch is LOCK.
AutoNDA by SimpleDocs
Connect the DST i and a PC with the USB cable. USB cable T01913E NOTE When the USB communication with the PC is established, the PC communication (USB) indicator on DST-i lights or flashes in green. When establishing the connection with the Bluetooth communication function on the models with Bluetooth, USB cable connection is not needed. If connecting with a PC with the Bluetooth communication, communication setup must be performed with the DST-i configuration tool. When the Bluetooth communication with the PC is established, the PC communication (Bluetooth) indicator on DST-i lights or flashes in blue. When connecting the models with Bluetooth to a PC with the USB cable, the USB communication has the top priority in the communication between a PC. When communication way is changed from USB to Bluetooth while communicating, remove the USB cable with the HinoDX finished.

Related to Connect the DST

  • Waist to Shoulder Full abilities Up to 5 kilograms 5 - 10 kilograms Other (please specify): Stair Climbing: Full abilities Up to 5 steps 6 - 12 steps Other (please specify): Use of hand(s):Left Hand Right Hand Gripping Gripping Pinching Pinching Other (please specify): Other (please specify): APPENDIX B – ABILITIES FORM Bending/twisting repetitive movement of (please specify): Work at or above shoulder activity: Chemical exposure to: Travel to Work: Ability to use public transit Ability to drive car Yes Yes No No

  • Right to Refuse to Cross Picket Lines All employees covered by this Agreement shall have the right to refuse to cross a picket line arising out of a dispute as defined in the Labour Relations Code of British Columbia. Any employee failing to report for duty shall be considered to be absent without pay. Failure to cross a picket line encountered in carrying out the Employer's business shall not be considered a violation of this Agreement nor shall it be grounds for disciplinary action.

  • Shipping must be Freight On Board Destination to the delivery location designated on the Customer purchase order The Contractor will retain title and control of all goods until delivery is completed and the Customer has accepted the delivery. All risk of transportation and all related charges are the responsibility of the Contractor. The Customer will notify the Contractor and H-GAC promptly of any damaged goods and will assist the Contractor in arranging for inspection. The Contractor must file all claims for visible or concealed damage. Unless otherwise stated in the Agreement, deliveries must consist only of new and unused merchandise.

  • DS3 Loop DS3 Loop is a two-point digital transmission path which provides for simultaneous two-way transmission of serial, bipolar, return-to-zero isochronous digital electrical signals at a transmission rate of 44.736 megabits per second (Mbps) that is dedicated to the use of the ordering CLEC in its provisioning of local exchange and associated exchange access services. It may provide transport for twenty-eight (28) DS1 channels, each of which provides the digital equivalent of twenty-four (24) analog voice grade channels. The interface to unbundled dedicated DS3 transport is a metallic-based electrical interface.

  • Right to Refuse to Cross Picket Lines‌ All employees covered by this agreement shall have the right to refuse to cross a picket line arising out of a dispute as defined in the Labour Relations Code of British Columbia. Any employee failing to report for duty shall be considered to be absent without pay. Failure to cross a picket line encountered in carrying out the Employer's business shall not be considered a violation of this agreement nor shall it be grounds for disciplinary action.

  • SHIPPING AND AIR TRANSPORT 1. Profits of an enterprise of a Contracting State from the operation of ships or aircraft in international traffic shall be taxable only in that State.

  • Website, Email Address and Toll-Free Number The Administrator will establish and maintain and use an internet website to post information of interest to Class Members including the date, time and location for the Final Approval Hearing and copies of the Settlement Agreement, Motion for Preliminary Approval, the Preliminary Approval, the Class Notice, the Motion for Final Approval, the Motion for Class Counsel Fees Payment, Class Counsel Litigation Expenses Payment and Class Representative Service Payment, the Final Approval and the Judgment. The Administrator will also maintain and monitor an email address and a toll-free telephone number to receive Class Member calls, faxes and emails.

  • DELIVERY: FOB DESTINATION, INSIDE DELIVERY, FREIGHT PAID Whenever possible, contractors should give the ordering entities 3 working days prior notice of any deliveries and/or installations. Furniture contractors will not be responsible for the removal/moving of existing furnishings unless requested by the ordering entity. Contractors should verify site readiness prior to delivery. All deliveries will be made during normal working hours unless otherwise arranged with the ordering entity. Contractor will communicate any scheduling delays and/or changes immediately. Agencies will not be responsible for any freight damage, concealed or otherwise.

  • Delivery Location All Goods shall be delivered to the address specified in this Order (the "Delivery Location") during Buyer's normal business hours or as otherwise instructed by Buyer.

  • Street Lighting 4.4.1 The Developer shall provide streetlights for the entire Subdivision at his sole expense. The type of lighting standard, pole spacing, and installation shall be per Memphis Light, Gas and Water standards. Memphis Light Gas and Water shall bill the City for installation of street lighting per its standards.

Time is Money Join Law Insider Premium to draft better contracts faster.