Bidder Supplied Samples The Commissioner reserves the right to request from the Bidder/Contractor a representative sample(s) of the Product offered at any time prior to or after award of a contract. Unless otherwise instructed, samples shall be furnished within the time specified in the request. Untimely submission of a sample may constitute grounds for rejection of Bid or cancellation of the Contract. Samples must be submitted free of charge and be accompanied by the Bidder’s name and address, any descriptive literature relating to the Product and a statement indicating how and where the sample is to be returned. Where applicable, samples must be properly labeled with the appropriate Bid or Contract reference. A sample may be held by the Commissioner during the entire term of the Contract and for a reasonable period thereafter for comparison with deliveries. At the conclusion of the holding period the sample, where feasible, will be returned as instructed by the Bidder, at the Bidder’s expense and risk. Where the Bidder has failed to fully instruct the Commissioner as to the return of the sample (i.e., mode and place of return, etc.) or refuses to bear the cost of its return, the sample shall become the sole property of the receiving entity at the conclusion of the holding period.
Information to be Supplied The Lessee shall —
Third Party Suppliers If Licensee wishes to obtain the Compound, Product and/or Licensed Product from a Third Party source, Licensee shall notify Pfizer through MPP of the intended source prior to making any commitments to purchase the Compound, Product and/or Licensed Product. Pfizer will determine at its sole discretion whether and on what terms to grant a license to the intended source to produce the Compound, Product and/or Licensed Product or inform Licensee whether such license already exists.
Water Supply The system may or may not meet state and local requirements. It is the right and responsibility of Buyer to determine the compliance of the system with state and local requirements. [For additional information on this subject, request the “Water Supply and Waste Disposal Notification” form.]
All new supplies equipment and services shall include manufacturer's minimum standard warranty unless otherwise agreed to in writing. Vendor shall be legally permitted to sell all products offered for sale to TIPS Members. All goods proposed and sold shall be new unless clearly stated in writing. Customer Support The Vendor shall provide timely and accurate customer support for orders to TIPS Members as agreed by the Parties. Vendors shall respond to such requests within a commercially reasonable time after receipt of the request. If support andƒor training is a line item sold or packaged with a sale, support shall be as agreed with the TIPS Member. Agreements Agreements for purchase will normally be put into effect by means of a purchase order(s) executed by authorized agents of the TIPS Member participating government entities, but other means of placing an order may be used at the Member’s discretion. Tax exempt status Most TIPS Members are tax exempt and the related laws andƒor regulations of the controlling jurisdiction(s) of the TIPS Member shall apply. Assignments of Agreements No assignment of Agreement may be made without the prior notification of TIPS. Written approval of TIPS shall not be unreasonably withheld. Payment for delivered goods and services can only be made to the awarded Vendor, Vendor designated reseller or vendor assigned company.
Payment for Forest Products Delivered Purchaser agrees to pay the State for delivered forest products at the following rate: $0.00/MBF $250.00/MBF for incorrect species delivery* $20/mbf for Utility logs (Adjusted Gross). Purchaser agrees to increase the above delivered payment rate as approved by the State in the event the location of delivery is changed per the G-026.2 clause. Purchaser will not be billed for any delivered logs that are scaled as containing metal. *When two or more log sorts from this project are delivered to the same destination, the species contained in them are not eligible for the species price reduction. P-036.2 Missorts and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet the sorting specifications in G-022.2 are considered mis-sorts. Purchaser receiving mis-sort Forest Products is required to pay the State at the bid price under this contract. However, when mis-sorted Forest Products amount to more than 5% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-sort threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-sort payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-sort price reduction are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-sorted will be calculated as follows: Payment Reduction = (B x M) x R Where: B = Bid rate from P-028.2 clause M = Mis-sorted volume exceeding threshold excluding utility R = Reduction factor* 0.2 for diameter mis-sort 0.3 for high quality mis-sort *Logs eligible for payment reduction based on multiple reduction factors will be calculated at the higher payment reduction factor. Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-sort payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-sorts shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code P-037.2 Mismanufacture and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet preferred log length specifications or multiples or combinations of preferred lengths and Forest Products delivered not meeting manufacturing standards as described in clause G-024.2 are considered mis- manufactured. Purchaser receiving mis-manufactured Forest Products is required to pay the State at the bid price under this contract. However, when mis-manufactured Forest Products amount to more than 8% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-manufacture threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-manufacture payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-manufacture price reductions are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-manufactured will be calculated as follows: Payment Reduction = (B x M) x (0.2) Where: B = Bid rate from P-028.2 clause M = Mis-manufactured volume exceeding threshold excluding utility Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-manufacture payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-manufacture shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Environmental Services 1. Preparation of Environmental Documentation (CEQA/NEPA) including but not limited to the following:
Warranty Services The Contractor warrants and represents that all services to be provided the City under the Contract will be fully and timely performed in a good and workmanlike manner in accordance with generally accepted industry standards and practices, the terms, conditions, and covenants of the Contract, and all applicable Federal, State and local laws, rules or regulations.
Engineering Services Definition: Engineering Services includes any service or creative work, the adequate performance of which requires education, training and experience in the application of special knowledge in consulting, investigating, evaluating, planning and designing, engineering principles. Engineering Services covered by the Xxxxxx Architect-Engineers Act (40 U.S.C. 1102) are not covered in the primary scope of OASIS SB. Examples: Service areas that are included under the Engineering Services discipline include, but are not limited to the following:
Authorized Sub-processors Customer agrees that MailChimp may engage Sub- processors to process Customer Data on Customer's behalf. The Sub-processors currently engaged by MailChimp and authorized by Customer are listed in Annex A.
